Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi,
I would like to flash a CC3100MOD wifi chip from TI with the Nordic 52832 chip as a host. Attached is my schematic. I am fairly new to the nordic family but I have...
Hi,
The problem statement mentioned below.
What we are trying to do is Read Light value from the MAX44009 sensor on the TWI interface.
Looking at the data sheet for...
Hi,
I am using Nordic nRF52840 SoC with nRF5_SDK_15.2.0_9412b96 (SDK) and S140 softdevice. I tried to set Tx power to +8dbm using
rc = sd_ble_gap_tx_power_set (BLE_GAP_TX_POWER_ROLE_ADV...
I am currently involved in developing a product that is using the nrf52840. The product needs to keep precise time across a wide range of temperatures, which is why a 32Mhz...
Hi,
When I try spi commnucation with sensor on nrf52840 (using Mbed OS with SDK14.2), it stuck to nrf_spim_task_trigger (p_spim, NRF_SPIM_TASK_START); while spim_xfer is...
Hi,
I am trying to increase the sampling rate of the motion sensor on a Thingy:52. I managed to update the firmware and increase the BLE_GAP_ADV_INTERVAL_MAX from 200 to...
I am using softdevice s132, nRF52832 and SDK 15.3
This happens every time I connect the RX line.
This is an application where I implement UART with the HRS application...
Hi,
I am interested to know how to make a mesh node (for example, a light server) compatible to perform a DFU.
I have gone through the DFU page and I noticed that the...
Hello.
I am about to receive the Uart service for the Nordic SDK Central and peripheral.
I Use nrf 52832.
In the peripheral example, we used 'ble_nus_data_send'...
Hi,
I am using nRF52840 Enineering C chip on a custom board using SDK v15.3.0 with SoftDevice v6.1.1
I have modified the Blinky Central code and the Blinky Peripheral...
Hi. After my nRF52832 peripheral connects to an android / iOS, I am trying to read the MTU size that has been negotiated with the following code;
current_mtu is being...
The NVMC writting functions hasn't return values,
void nrf_nvmc_write_bytes(uint32_t address, const uint8_t * src, uint32_t num_bytes)
Does it mean that all internal...
When nRF52840 P0.09 / P0.10 are used as GPIOs, the datasheet indicates they can be used for "low frequency I/O only". What is the frequency limit on these pins? Would it be...
