I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I'm using nRF5_SDK_14.0.0_3bcc1f7 and SD132 v5.0.0. In response a DATA_LENGTH_UPDATE_REQUEST event, I'm calling sd_ble_gap_data_length_update as follows:
ble_gap_data_length_params_t...
Hi,
I am using nRF52832 with S132 softdevice and SDK version 11. I am getting bad memory address error code.
err_code = sd_ble_uuid_vs_add (&base_uuid, &ble_service->uuid_type...
Hi
I have a softdevice assert problem when i run the "nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject...
we use
peripheral: exemple ble_app_blinky
central: exemple_ble_app_bliky-c
Instead of a button we have a Switch.
When we set the Switch to "on" the led go on.
That...
Hi, I made a device with using NRF51822, named 'allb' the wearable device for babies.
http://myallb.com
We're planning to make a new version of it with using nRF52840...
The firmware used operate properly in the past, but it no longer does after we replaced the MCU(nrf52832).
During SOFTDEVICE_HANDLER_INIT, the MCU is stopped.
The previous...
I am working on a peripheral. This peripheral is IO display only. On the other side, the central is keyboard + display. I have a single, custom service with a single characteristic...
Hi All,
I did this tutorial : How Import a Keil uVision project Segger Embedded Studio - A Cross Platform IDE ,
but I dont know what did wrong. I still get this error...
While porting my app to the latest 14.0 SDK, it got a little stuck with the new sdh library. I was previously fetching all events through a custom poll & wait loop, but I...
When a packet sent out and get the TX_DS IRQ by nRF24l01+, the mode change to RX and read STATUS register then write the value to the STATUS register and write FLUSH_RX 0xff...
For the SDK13.0.0 the documentation say that HF clock is activated in nrf_drv_usbd_enable() / app_usbd_enable() but it is activated in nrf_drv_usbd_init() / app_usbd_init...
Hi,
We are planning to build a Mobile application for IoT involving Bluetooth communication. We came across a few part numbers of Nordic for this. We would like to know...
I had purchased the Red Bear Labs "Micro" board to develop code using their MK20 USB Dongle and Arduino.
If I "hack" the programming cable to emulate the "Micro" daughter...
Hi ,
I have recently bought a nRF5232 PCA10040 development kit and i am trying to interface nRf52832 development kit(Master) with AS3955(slave) over twi. I tested the twi_scanner...
Hi all
I'm trying to build a generator based on NRF52832. Outpit signals are: 8MHz clock and two latches signals highly sinchronized with clock - RGB_LAT and TXT_LAT. For...
