SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Can some one describe how this is supposed to work:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/mpsl/timeslot/README.html
I would have expected to see...
Hi,
I wonder if anybody could help me? What is the best way to close down the nrf9161 so that it reconnects quickly after powering back up again?
I'm running Zephyr 2...
Dear Nordic Support Team,
In the datasheet of the nrf9160 (nRF9160_PS_v2.2.pdf) the VSS pin appears in the section 6.4.5.1 GPIO Electrical Specification, but I cannot find...
I am preparing to make our first firmware release on our custom board, which is equipped with the nRF9160 SICA B1 , modem fw version 1.3.4 . Our application is based on the...
I've been running into a lot of issues where a change in the configuration for the application results in an answer that basically states:
"You're supposed to add this configuration...
Hi all!
I'm wondering why the VS Code has option to create a new board for the nRF5340-QKAA only?
I have on hands the nRF5340-CLAA and nRF7002 chips which I'm going to...
Hi,
I'm currently building a product that uses PSA crypto API to generate, and save some keys in secure storage. I also need to have a WiFi functionality (nRF7002), but...
I have been able to connect and initialize two different Bluetooth OBD II Devices. I am running into issues with the third device I am trying to add as an option. I add the...
Hi,
nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect
We need to implement a multicore application for nRF54H20. I...
Hi,
I have a question concerning time zone support in nRF SDK >= 1.9.1 for nrf9160.
I'm trying to implement an LwM2M client that should be able to convert a UTC datetime...
NCS 2.7.0/2.8.0
mcuboot + MCUMGR in the application for BLE DFU
NRF52840
We have been developing our next version of our product, transitioning from NRF SDK 5 to NCS...
Hi，
When I used NCS V2.5.0,after two devices successfully establish a BLE connection but then disconnect due to a timeout, subsequent reconnection attempts fail with error...
I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hi,
I'm trying to test DTM over USB CDC with an nRF5340DK unfortunately, Direct Test Mode desktop App is not detecting the DK.
Build command (copied from VSCode output...
