I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi,
There is a bug in ncs\v2.7.99-cs2\nrf\cmake\version_app.cmake
add_custom_command( OUTPUT ${PROJECT_BINARY_DIR}/include/generated/app_commit.h COMMAND ${CMAKE_COMMAND...
I am using nRF Connect fro Desktop Bluetooth Low Energy Standalone v4.0.4 with a Dongle USB nRF52840.
I can see my device when Legacy Advertising is enabled, but if I only...
Hi,
First of all, let me confess, I am new to VS Code - NRF SDK environment.
I have a VS Code setup with NRF extensions enabled and due to some reason, the error squiggles...
Hi , I 'm trying to send and receive on a websocket. Sending works fine and is received on the backend, but when I try to receive I just get garbage in my buffer.
I sanity...
Hi,
I'm currently trying to add MCUBoot in my project.
The project was built successfully by adding these lines to prj.conf.
CONFIG_BOOTLOADER_MCUBOOT=y
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
I'm looking into using command line builds for nRF Connect SDK again due to issues I've been running into with vscode.
The instructions on this page ( https://docs.nordicsemi...
I have tried zephyr/sample/bluetooth/periodic_sync_conn in nrfsdk v2.7 and test on nrf5340 audio dk, and doens't work. the output is:
*** Using Zephyr OS v3.6.99-100befc70c74...
Hi,
How to solve the problem of writing data to flash using the write_data_flash function in save_stack_data function
1.1. I tried to add the function save_stack_data...
Hi! Background (feel free to skip) --------------------------------------- We have 3 nRF52840 boards, connected via ble/NUS as follows:
B also advertises bluetooth HID...
Hi, we are using the nRF9160 in conjunction with the nPM1300. To power off the device, we call lte_lc_power_off() which sends the AT+CFUN=0 command to the modem and waits...
the v2.7.0-5cb85570ca43 zephyr/ndk combination doesn’t work for things using the JSON_TOK_FLOAT type (vs the number type). this is because zephyr/lib/utils/json.c:float_ascii_encode...
I am working on a project in which i have got 100 nodes we are doing it in our custom board. so i need to assign unicast address manaully for each nodes inside it. How can...
When I try to build any application with west I always get a CMake error complaining that it is unable to run the Python version included with the NCS toolchain. The error...
I'm working with a DVK that has an nrF52840 with a Sierra Wireless HL7800 modem. The modem is connected physically to UART1 while the UART0 is used for the following as shown...
