I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
The question is as follows：
When I read the ADS1299 data through SPI in the GPIOTE interrupt, I found that there was a time limit. Within about 50us. As shown in the figure...
Good morning
Doing the BLE fundamentals course and cant seem to build lesson 4 ex 3. Have picked up this thread BLE Fundamentals lesson 4 exercise 3 failure to build ...
Hello,
I have started working with the nRF54H20 by following the guidelines mentioned in the nRF Connect SDK Fundamentals course.
In Lesson1 Exercise2 I'm facing following...
I'm using the Thingy52 circuit in some other projects, and the built-in speaker is not loud enough for my application. I'm looking for an amplifier that can be connected to...
Dear,
We are currently developing a communication board for a client that uploads large images (~1MB) to the cloud via local and remote interfaces, and we've encountered...
Hello! I'm currently trying to scope out chips that let me do Bluetooth Classic + BLE via a UART HCI link. I came this module and noticed that it uses the NRF5340.
NORDIC...
Hello everyone,
I'm currently working on a project wherewe use the ANNAB402 and Zephyr as out RTOS. We are developing using VSCode on a Linux VM. With a new board from us...
Hi ,
I am using nrf52840 as a peripheral HID Remote control with multi-connections, and it is able to connect with all devices like phones, computers, smart televisions...
The out-of-box configuration of Thingy 52 has a 89dB, 8 ohm, 0.7W speaker.
Can I replace that with a much louder speaker such as 4W or 5W one 4 ohm or 8 ohm?
44
I am programming with the nRF52840DKs. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am currently working on integrating...
Hi,
We're currently facing an issue with Bluetooth Low Energy (BLE) range on our custom board using the NRF5340 with SDK version 2.6.1. During testing, we observed a significant...
We are migrating the firmware of our devices from Nordic's Mesh SDK 5.0.0 to Zephyr 3.5.0, starting with the provisioner device. The SOC we use is the nrf52840 and we use...
Hi, do i need to place external hardware (antenna ?) in order to be able to read the NFC info of the board?
According to the peripheral_hids_keyboad sample:
"When the...
Is it possible to enable and disable the ADC peripheral of nRF52840 to save power in nRF connect SDK? In our application, we use ADC to get battery voltage samples after every...
