Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Currently, I'm using the NRF5340 chip. In my own development board, I'm only powering the chip to test its transmission performance. The example program I'm using is the classic...
nRF52840 using Zephyr 2.0.0
We currently have a system that after we are running can drop to 20uA. However, on boot, we draw something like 5-7mA. This large on boot current...
I work on a project with nRF52833 ( NRF Connect v3.0.2 currently) and I have to use an external AT45DB641E flash chip connected over SPI .
The external flash will be mainly...
example: ncs/v3.0.1/find my/pair before use I want to implement the ptx and prx of the ESB in the find my example "pair before use". That is, how do I operate when both BLE...
In our application we need a PPS signal even when LTE is enabled (and GNSS is disabled). The GNSS API gives some encouraging PPS info, stating " GNSS only starts giving pulses...
The current specifications (v0.8) for the nRF54L series of parts provide very little information about the input impedance of the SAADC peripheral. There are no values specified...
We are currently facing a troublesome issue: we need to send 242-byte data packets at a fixed 3ms interval. We connected an LED light after the data transmission module to...
Dear Nordic Support Team,
I hope this email finds you well.
I am writing to seek your assistance with a build issue I have encountered while using the nRF Connect SDK...
Hello,
I have already implement the RSSI2 monitoring where I get the RSSI2 value with each successfully received packet via pcd-callback and its attached nrf_modem_dect_phy_pdc_event...
The app can work well in nrf52810 QFN48,it can't work as design in QFN32.
I have created my module with nrf52810 QFN32, loaded softdevice,loaded app,enter debug mode with...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
Hello,
I am building my own board with the nRF9151. I see that it can do SPI, but it does not say what pins are SPI capable. As the chip is a SoC (or CiP), can I use any...
Looking at the datasheet for the nrf54h20 it lists GPIO port P9 as Slow and Analog.
However, in the pin mapping, it also says SPIM130 and SPIM131 are available on port...
Hello,
We are trying to run 802.15.4 alongside our BLE Mesh network on the nRF54L15.
However whenever compiling with CONFIG_NRF_802154_RADIO_DRIVER =y, we run into the...
