I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
On nRF54L15 (NCS v3.1.0), we are using the SAADC with ADC_GAIN_1_4 and ADC_REF_INTERNAL at 14-bit resolution to measure an analog voltage on AIN5. The driver sets ref_internal...
Hi.
I am attempting to obtain SIG certification.
I am using ncs v3.1.1 with nRF52833.
Based on the link below,
https://docs.nordicsemi.com/bundle/comp_matrix_nrf52833...
Dear NORDIC engineers, excuse me. I would like to inquire about the Settings of NRF54LM20 APPPROTECT. I have modified APPROTECT[n].protect0 and APPROTECT[n].protect1 to 0x5A5A5A5A...
I am trying to use the nRF54L15 DK board to flash a Fanstel BM15M module.
Fanstel BM15M module link: Fanstel BM15M Module
I am using the nRF54L15 DK board with the external...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I have a nRF9151 dev kit for evaluation that I am following official guide to get up and running using the asset tracker v2 program. I can flash the firmware but I cannot...
I want to expand the flash allocated to mcuboot on the NRF desktop, but it failed to start after compilation
The following is a flash layout that can be successfully launched...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
I have successfully completed the one script install of Zephyr on RPI and can fully develop Nordic nrf52832/nrf52840. I assume all other supported boards within Zephyr can...
I'm trying to advertise an isochronous IN endpoint with wMaxPacketSize = 768 bytes (8 channels × 48 kHz × 16-bit audio, 1 ms polling). USB init fails at usbd_init with Failed...
Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
I measured the power consumption of the BLE RX using the nRF54L15.(nRF54L15-DK v1.0.0) 3.0V operation apps: scan_adv (delete advertising) west build -b nrf54l15dk/nrf54l15...
Hi Nordic Team,
I’d like to ask: Does the recommended Bluetooth matching circuit for the nRF54L15 need to be designed as a bandpass filter?
Also, do you have the VNA...
Hi devzone, I'm working on the nRF54L05, having an application and the mcuboot generated correctly on my host computer. Now we want to generate the binaries on Bitbucket pipelines...
