I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
I've used PCA10040 sdk15.0 example ble_peripheral ble_app_uart
I can handle it through terminal.
If I insert strings through terminal, App can receive.
But, I...
hii,
i am trying to interface the nrf24LU1+ and nrf52832. I wanted to know if i can program the nrf24lu1+ without the requirement of nrfgo motherboard. or is it necessary...
I don't want to use MESH， because there are too many data
Application scenario
Mobile phone ------------> DeviceA --------------------------------------> DeviceB
...
Hello,
Would there be any particularly adverse side-effect if two NRF51822 GPIO pins (e.g., P0.18 and P0.19) were shorted together? One of the pins (e.g., P0.18) would be...
SDK ：15.0.0
Examples：ble_peripheral / ble_app_uart / pca10056 / s140
Board：nRF52840 DK
After pairing, may be connected, because the indicator lights continue to shine...
Hi,
I am using sd_ble_gatts_characteristic_add to set a characteristic in my service. The function call return 0 - NRF_SUCCESS but when I browse the service with nRF connect...
Hello,
I try to add pairing functionality to my app. Error code NRF_ERROR_INVALID_PARAM occur from the sd_ble_gap_sec_params_reply when i want to read my characteritic...
Hey, I have a sensor (ADC with data rate is 250 sps), attached to nrf51822. It has Data ready pin (output), which toggles from high to low when data is ready. Also this sensor...
Hi, I'm using nRF52832 with my custom board. (sdk 15.0.0)
I changed ble_uart example code, so I can receive GPS data through bluetooth.
Now, I have to send GPS data to...
Hello all.
few years ago, I made some product using nRF51822 on SDK v10.0.0
currently, I have to software update to use ECC(Elliptic Curve Cryptography) function on...
I'm using: nrf52832, SDK 15.0, SoftDevice S132 v6.0.
I'm trying to control a motor using an H-Bridge. If I simply do a nrf_gpio_pin_write to set forward/reverse to 1/0 or...
I have the nRF52832 PCA10040, V1.2.1, 2017.23 development board with ble_app_blinky_gcc_nrf52.ld RAM/FLASH settings:
MEMORY { FLASH (rx) : ORIGIN = 0x26000, LENGTH = 0x5a000...
Hi,
My freertos based application (SDK14.2) calls battery monitoring procedure every few minutes .
I've initialized the SAADC
Within the function I call
...
Hello, I have nrf52 and configure uart0 for connection with external device. I have configured it as NRF_SERIAL_MODE_DMA and set irq_handler .receive NRF_SERIAL_EVENT_DRV_ERR...
