How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
When uploading a network core image though MCUBoot and confirming the image, sometimes it fails to accept and on other builds it accepts the update.
I have narrowed this...
Hi
Greetings, Hope you are doing well.
I am fairly new to using the nRF Connect SDK through VS Code. I completed the nRF Connect SDK Fundamentals course, and I also noticed...
Hi All,
I am currently working on an project with the nRF9151 using the nRF SDK v3.1.1 and MCUboot and I need to sign my application images using an external HSM. I am using...
I am having this problem in my Macbook Air M4. It times out when flashing the application via nRF Connect SDK extension. I also tried to run the nrfjprog command myself and...
I’m evaluating the nRF Connect SDK Bare Metal SDK and hit an issue with the bm_storage library. bm_storage_write() and bm_storage_read() work correctly, but bm_storage_erase...
When using GNSS periodic mode with nrf_modem_gnss_fix_interval_set() set to 20 minutes and nrf_modem_gnss_fix_retry_set() to 5 minutes, the actual wake-up intervals are inconsistent...
Hi,
I have a feeling we may be experiencing Modem Reset Loop Restrictions on some of our devices, so I want to put in something to our application code so we know and can...
Hi ,
I need to do create the bootloader . generally what we dump in to the board was the firmware not bootloader right. I want to do the OTA updates on the nRF52840 Dev...
Hello,
I am currently using nRF Cloud to perform FOTA updates on my nRF9160 devices. I have multiple certificates on this device.
1. TLS certificate for my application...
I need to store a hardware-revision value on an nRF9160 during manufacturing (using something like nrfjprog ), and the non-secure application firmware must be able to read...
Hi
I’m working with an NPM1300EK connected over I²C to an nRF54L15 , and I’m seeing an issue where the VBUSINSTATUS register consistently reads back 0x00 , even when VBUS...
Hi,
I’m working on nRF9151 with nRF Connect SDK 2.9.0 , and I’m facing a FLASH overflow issue when enabling dual-image OTA (primary + secondary partitions) . Our project...
Issue Summary
fds_record_update() in SDK 13.0.0 creates permanent duplicate records instead of replacing old records. This causes:
Valid record count to grow indefinitely...
Hi Nordic support:
Our project uses the nRF9151 and QM13545 MIPI RF SWITCH. We have a question about AT%XMIPIRFFECTRL command's frequency: If the frequency switching point...
Hello,
I encountered a very strange problem. This problem originated from my development of RGB color lights using the NRF52840. Due to the limitations of RGB color lights...
