Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello, I am trying the nRF9160 DK for the first time and when I try to connect my DK to my laptop and select my device in the nRF Connect Programmer it shows the error highlighted...
Hello, I am trying the nRF9160 DK for the first time and when I try to connect my DK to my laptop and select my device in the nRF Connect Programmer it shows the error highlighted...
Hi all,
Because of my customer special requirement ,I need two or three USB in my project .
But 52840 has one USB.Can I extend 52840 USB interface with a USB HUB?
With SDK V14.2, I was able to specify internal flash address argument into nrf_bootloader_app_start(uint32_t start_addr) and was able to boot into the address. With SDK V15...
Hello, I have a problem when trying to compile the light server exemple for the mesh.
I use Segger Embbeded Studio 4.16 (even though i tried the 4.15), mesh sdk 3.0 and...
Hello,
I'm using NRF52840 module to make a customer device. I'm using nRF5 SDK for Thread and Zigbee v3.0.0.
I have a Thread mesh with some routers devices and one child...
I saw this BLE security issue and was wondering how Nordic deals with it. When the other side uses the example LTK from the BLE spec, can the softdevice automatically reject...
Hi,
Here's I want to do: Use static passkey to connect with central and peripheral. I'm useing peer_manager to doing this. 1. I've setup passkey in peripheral with function...
Hi,
while I tried the Power Profiler in the nRF Connect Desktop on OS/X, I got some error messages in the log (something like PPK Command Error). So I've installed the newest...
I run blue_app_hids_keyboard_pca10056_s140 sample on nRF52840-DK. I try to connect with Windows 10 PC, but PC does not discover Nordic_Keyboard.
I found advertising is sent...
We have a PCA10090 board and I followed all the steps of the nRF Connect SDK to install everything, including the files from repository, SES, etc. All is ok but I can't find...
Hello, I am working on a project that uses nrf52832 and I need to put that device and in the system on mode. For that, I want to measure the current in the system on and system...
The PWM (Pulse Width Modulation) peripheral coupled with EasyDMA makes an excellent waveform generator. However it has one drawback which I would like to request be added...
Hi, i use the saadc example(triggered by ppi+timer) with uart to get voltage signal and transmit to central device( another custom nrf52832 board), and the central prints...
