Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am runing the light switch example in zigbee sdk v3.1. I am connecting to a smarthings hub. I have set the a single change on the code:
The device will be connected...
A couple questions about the nRF52840 GPIO Electrical Specification:
1. In the nRF52840 GPIO Electrical specification, VOH at 0.5mA is spec'd to go as low as VDD - 0.4V...
Hello,
I have been using the development kit for more than a month when after one flashing, the LED 5 on the board started blinking at one second intervals and the board...
I read a nRF9160 DK 0.8.5 circuit design and have a question about the GPS circuitry. What will happen if I bring the LTE antenna closer to the GPS antenna and reduce the...
Hi,
We have a program that uses the radio driver for IEEE 15.4. Currently we do not need Bluetooth and IEEE 15.4 working simultaneously but we do need Bluetooth DFU. When...
Hi,
Just spent a while debugging this and since there seems to be nothing - well I can't find it anyway - up here thought I should document this issue. This relates to SDK...
hi ...
i am using nrf toolbox (ble uart )to receive data from nrf52832 ..i am receiving the data for every one minute . i am facing the issue in auto connect see the below...
Hi,
Actually I am interested in making the custom design Board for the nRF52 series , so where can i find the schematics , layout files of the nRF52 Development Kit ....
Using s140 for the nRF52840 is it possible to have a BLE multilink connection (up to 8peripherals) with an extended MTU size (around 70bytes)?
All examples that I have seen...
Dear Team,
would a solution like this be possible with nrf91? http://rxnetworks.com/location-io/predicted-gnss-ephemeris/
> a reduction of Time-To-First-Fix from 45...
Hello!
Could you show me an USBD configuration example which works fine with Arduino serial monitor? Because Arduino serial monitor froze when i send a string , but when...
In the nRF52832 (Laird BL652 module) I have programmed.
MBR + SoftDevice from 0x0000 0000 Application from 0x0002 6000 ~ 0x0005 927C
Now trying to program additional application...
Hi
Is there any documentation regarding bluetooth in nRF52832 specs sheet or anywhere else? I understand that there are examples provided by SDK. But I want to know in detail...
Hello,
we are running BT certification on product with nRF52840 chip. It seems that TCRL-2018-2 is now mandatory.
Did someone know if the QDID certified TCRL-2018-2 is...
I am not able to program the nRF52840DK by copying over the .hex file generated by my project to the JLINK drive. However I am able to successfully program using Segger directly...
