Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
SDK Environment: nRF Connect SDK v1.7.1 Target: Decawave DWM1001-DEV. This uses the nRF52832
Simon posted in this discussion an example of adding a custom service to the...
Dear Members,
I followed the step on :
https://devzone.nordicsemi.com/f/nordic-q-a/71299/getting-hardfault-error-when-using-ble-lesc-pairing/292979#292979
and I got...
Hi,
I'm developing with 52832 DK. I used 'CONFIG_NFCT_PINS_AS_GPIOS' to config pin9, pin10 as general GPIOs and set pin10 to SPI_MOSI. However the system crash when applying...
Hi,
I am creating a BLE communication device (peripheral) using softdevice S132 (v7.0.1) and SDK 16.0.0 on the nRF52832 microcomputer.
I have implemented the BLE communication...
Hello,
I'm new on Nordic environment, I'm designing a RF module that require low latency to transmit few bytes (less than 10) in less then 10ms from a triggering input...
Hello,
Referencing the specification , the time it takes to complete the COMPARE task upon triggering is not directly outlined.
I would like to have the following function...
Hi,
I've installed VS Code 162.3 on Windows 10 machine via Toolchain Manager. I've also installed nRF Connect extensions for SDK v1.7.1. The build system works under NCS...
We need to know the list of configurations to explore more like the following configurations in proj.conf file
for C++ files we enable following configurations in proj...
I use cli library functions for serial port communication, using macros to define m_cli_uart and m_ m_cli_uart _transport variables, program compilation is no problem, when...
Hello everyone,
I used the Multirole example as base for my code. My target is to make a communication with two NRF52382. I changed the HRS (heart rate servide) to my custom...
Hi,
I am using the PCA10040 DK (v1.1.1) to measure the current consumption in sleep mode and the current is about 200 uA. (3V, DCDC Enable)
Following is the code, it...
I'm new to the nRF Connect software and I'm following the helpful "nRF Connect for VS Code" video series on YouTube to install it on my Windows 10 PC. Everything was going...
hi support team,
customer has one question about about sd_ble_gatts_hvx notify API, found that this data is not sent out immediately, but there is one connect interval...
HI,
i building nrf5_SDK_for_Mesh_v5.0.0_src got error undefined reference to `NRF_LOG_DEBUG'
nRF5_SDK_17.0.2_d674dde , DK10056 52840,
i put it the same dir and seted...
