Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
The nRF connect program for desktop
https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-desktop
Will it be updated to fully support Bluetooth 5? Extended...
Hi,
I got a problem with sending data via gazele protocols, i'm using example library gzll_ack_payload_ host and device, can somebody explain me how this code works?
i...
Hi.
I'm working on macOS Monterey 12.0 beta and trying to start nRF Connect for desktop (version 3.7.0). When i'm trying to start this application it's starting as blank...
Hi.
This question is to confirm again about below.
Is it possible that implement multiple advertising sets, some of them would be 1M and some would be CODED PHY. And...
I'm trying to set up VS code to use it with the NRF Connect SDK. I've created an application from basic/blinky example. My problem is VS code can't resolve any inclusions...
OK, like many people moving across from a different IDE/SOC environment, I'm finding navigating my way through setup and programming with Nordic SOC, even of simple tasks...
I've run into two oddities with the Connected Devices feature of nRF Connect for Visual Studio Code and two different nRF52840 dongles that are connected via a J-Link. In...
Hi,
I try to use zgp api and first try to call zb_zgps_delete_all_zgpd() but I receive an error from linker:
undefined reference to `zb_zgps_delete_all_zgpd'
Is there...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am using openthread protocol...
We want to use GPIO_12 as a wake up pin. (High -> open uart, Low -> close uart) Also, we have a timer and timeout set to 500ms. When we pull GPIO_12 to high, it seems not...
I'm working on NCS 1.6.1 for both nRF52840 and nRF9160.
I'm trying to put my devices into sleep mode so i reviewed some related tickets and found following ways.
NRF_REGULATORS...
Hello,
I am quite new to NCS. I am trying to sending UART data from nRF52dk_52832 to PC.
The example is nrf\samples\peripheral\lpuart.
If I enable the example with CONFIG_LOG...
Want to realize a function: stop broadcasting after a broadcast, update the broadcast content, and then start broadcasting again after the specified timeout. How can I judge...
