Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
I just got started with the nrf9160 DK and I tested it with the Asset Tracker application (following the getting started video). At first everything was working fine and I...
If I am creating an application using the Zigbee stack running with nRF Connect SDK and Zephyr, what hardware is not available to me because it is already consumed by the...
I have both a NRF9160DK which I can program and, Zephyr, blinky Serial modem etc, all work on the DK and I also have a nrf91 Thingy.
The Thingy won't respond to programming...
Hi Nordic
One of My customer employs nRF52832-QFAA in their product. They use SDK 17.0.2 and SES to develop their product。
They found the flash is now enough(they use...
I have a NRF52840. To save some energy I wanted to disable the soft device so that there's no bluetooth activity at all. However instead of an average consumption of about...
I am developing BLE Mesh product with `nRF connect SDK`.
I understand most of sample project has a function of proxy node. But I don't know how to connect a provisioned...
I've upgraded several Thingy91 boards successfully with the latest firmware and have ran into an issue with another Thingy91 that I've purchased. Here is the error when I...
Hi,
I am storing sensor data into flash and sending it to client when it is requested by Indication characteristic.
I don't have any issue with reading/writing/updating...
Hello developer,
I am new here and learning Beacons with the Board nRF52840 Feather from Adafruit as scanner and Segger Embedded Studio. I refer to nRF52 SDK 17.0.2 and...
Hi all,
I have connected my PPK II to my pc (Ubuntu), installed the software and connected the device.
I can't seem to find the mode or start button anywhere on the user...
Hello everyone,
I am using the fanstel BC840, where the tx and rx pins of the uart are alloced on 1.02 and 1.01:
So i have created a custom_board named hello_board...
Hi,
I’m trying to test/confirm the accuracy of the 32kHz crystal oscillator and the 32MHz crystal oscillator by toggling a GPIO at a derived rate and at 50% duty. But I...
The tag options did not include just nRF Connect as an option so I picked something that had nRF Connect in it. This issue has nothing to do with the SDK.
This is a question...
Help me simple LED Blinkink nrf51822 AA type i'm using YJ-14015 and stlink compiler.. i'm also using keil for IDE. i don't know how to create program and setting for compiler...
