How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I define the following macros in "Section Placement Macros".
Can I use these macro values in my...
When the boot loader calls the sd_mbr_command it does not get updated.
sd_mbr_command_t sd_mbr_cmd;
sd_mbr_cmd.command = SD_MBR_COMMAND_COPY_BL;
sd_mbr_cmd.params...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I recognize by default that the top address of the app is 0x26000. I want to change the top address...
I need to measure current of loads attached to NRF52832 using current transformer(CT).
I can use SAADC library to read ADC value. But to measure current I have to know the...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) deviceA: EYSHJNZWZ (nRF52832) deviceB: Android (ver9...
Dear All,
We would like to automate the trst procedure of our device in LabWiew because in this tool we are doing also electrical measurements.
We have tried nRF connect...
Hello,
I'm running custom firmware on a nRF52840 based DK (Rigado BMD-340).
The log from the nRF Connect app is as follows:
Could anyone help explain the error...
Hi,
I am using nrf mesh sdk v3.2.0 and I would like to combine our custom service within the mesh server example (includes the proxy service). Using info from other threads...
We are having issues with UART communication on the nRF52840. Using a logic analyzer, we have found that the transitions happen too quickly. This causes the receiving MCU...
I have been working with Thingy:91 for three weeks now. Everything works nicely, however, I could not get any GPS location from it. I am using Rogers simcard which is a local...
Hello everyone. My project is getting quite complex so I will try to abridge. (Mesh SDK 3.2.0) I am trying to send wifi credentials from an android application (derived from...
Hi guys,
here in Croatia I'm trying to connect to NB-IOT network using nrf9160.
Here are the commands i am executing:
After this command modem does not accept any...
hi all,
i build project use HCI controller with nrf52840 , it some time show error message,
how to deal with this issue
HCI Host Not enough space in buffer #hci
https...
Hi,
I am working on a development where the values of a bunch of nodes with a sensor needs to be captured in one aggregator device in a mesh network. The aggregator then...
