In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello,
I want to install my own Button & LED handling (not using the default board support). It works on the nRF52840 Dongle, but I also want it to work on the PCA10056...
Hi Nordic,
I have tested the example, the softblink is working by configure the structure below:
typedef struct { bool active_high; /**< Activate negative polarity....
We are developing a BLE Beacon using the SDK v12.2 and the softdevice s132 on a nRF52832 chip. The code works on the DevKit successfully but it doesn't work on our custom...
We found the devices developed with nrf51 and nrf52 will disconnected from the iphone sometimes, and we can't find the real reason.
I study the gap parameters on nrf51 and...
Hi there,
Seems that the flashlog read processes a log entry from flash using nrf_log_std/hexdump_entry_process, which does take care of the formatting string in the entry...
I have successfully implemented DFU over the Air function using Android-DFU-Library (Github) for my Android mobile phone.
The Android-DFU-Library needs Android 4.3+ at least...
Hi, I am after a bit of advice regarding the SPI interface between a nRF52832 acting as a master, and 3 slave devices. I only need to communicate with one SPI device at a...
Hello,
my goal is to measure the average current consumption of an external chip connected to the Power Profiler Kit on Windows 7. Since the Software inside the nRF Connect...
using SDK 12.1.0
The original error (compile time only) is
main.c(338): error: #94-D: the size of an array must be greater than zero
my snippet @ line 338:
SOFTDEVICE_HANDLER_INIT...
We run SR3 on android system which is working , need change system to embeded linux .
we run SR3 on embeded linux , i can't use voice function .
we get son info: https...
I wanted to use the sdk board support file with coustom board having 13 buttons. I have modified the bsp.c and configer number of low power events and added a coustom header...
Hi,
i have interfaced a ADC device in the nrf2 development kit,i am getting the values from the adc after using the SAADC example,
i want to implement the same with the...
Hi softdevice uses s130 The board is using nrf51 dk. The example uses the ble_app_beacon example from sdk12.3. if (switch_hit ()) { // NRF_POWER-> SYSTEMOFF = 1; // sd_power_system_off...
Hi Team,
Being trying to run the Thingy 52 mesh demo following : https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
I am using pre-built .hex file Thingy_node_s132...
Hi there,
Recently I bought an LTE module which uses a nRF52840 as the main processor to control the modem, I want to erase the flash for that module and flash the project...
