I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hi
I had used one nRF52 Kit(nRF52832+nRF5_SDK_14.2.0) to connect a BLE 6LoWPAN Border Router(Raspberry Pi 3B+Raspbian)
according to the IoT User Guide.
But in IoT applications...
i am using ubuntu 16.04
using eclipse photon IDE
nrf52_14.1.0 i am unable to run to run more than two threads can u please help me out in this
i am trying "nRF5_SDK_14...
Hi,
I am working with bonding process on Android App.
My problem is:
When I create bond to nrf51822, the process complete successfully. Then after a few seconds (3-5...
Dear Nordic Team,
Thanks for supporting .
I have a custom hardware for nRF52832 its working for nrf_beacon example but its not work with eddystone beacon example.
please...
We’re working with the NRF52, SDK 14.2 and SES.
Somehow we have managed to have our boot loader extend into our MBR params page. We extended the stock SDK 14.2 boot loader...
So using the above code I am trying to set the threshold of 2.3 volts on the power comparator. I am using sdk12.1 with Soft device 3.0.0 on an nrf52832
I keep getting NRF_ERROR_SOC_POWER_POF_THRESHOLD_UNKNOWN...
board nrf52840
sdk 15.2
hi i have one problem in connection, once i connected the device and disconnect means ,the device stops advertising..if i reset means it will show...
Hi, I have a problem when write data to flash on nRF52832. my code is like below:
err_code = nrf_drv_clock_init(); APP_ERROR_CHECK(err_code); // Activate deep sleep mode...
Hi Nordic:
I migrate my application from mesh-2.1.1+sdk15.0.0 to mesh2.2.0+ sdk15.0.0, but there is an issue when calling mesh_stack_config_clear()
Following are my steps...
Hi,
I'm using nRF51 (softdevice S130) in my project as BLE peripheral to send data to my smartphone. The current data flow has become insufficient because the maximum MTU...
Hi.
I tried to use SES 3.5, but can't found Text Editor Environment in
Tools -> Options... ->
In 3.4, I can find it in
Tools -> Options... ->
Does anyone know...
