I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
hi!
I use the reference design of nrf52832_ciaa.IntLib ,but it didn't work
I use the internal-LDO ,but i measure the voltage of DEC4, it's 2.5V(not 1.3V), the VDD is 2...
Hello,
I am developing a BLE application using the custom characteristic example provided by nordic. I have added a few characteristic for the same.
I am having a small...
I am just trying to establish communication between spi master and spi slave.
I am using two nrf52 boards, SDK 15, in one i dumped spi master example and in another i dumped...
Hi,
I have a customer developing with the nRF8001 with an external MCU, a PIC32MM. He is interfacing the the device with SPI and he is struggling to set up the device and...
Dear support team,
I'd like to provision a mesh node which is implement on thingy and without proxy feature.
As I know, the BLE device (mobile) should communicate with...
hello I am new on nrf52 and I would like to run the example for the ant+: "bpwr_tx".
I am on a nrf52832 chip (with a pca10040 1.2.4 demo board ), I am using nRF5_SDK_15...
Hello,
I used nrf52832 as a scanner.
Now i use it to scan only one tag. And the TAG advertise data addcoring to ble 4.0.
Now i find scan channels are not 37,38,39,37...
■Development environment nfr52832 SDK_12.3.0
■Question I'm making Central's module. After connecting with a peripheral of pairing finish, the function(pm_peer_rank_highest...
Hi all,
I am trying to test OpenThread protocol for an application that we have and we want to use the CLI interface as the application logic should stay in the application...
Hi all,
I was in the process of buying 3 nrf52-dk boards. I need to know if one can differentiate all of the different boards on their PC when connected at the same time...
Dear Nordic Team,
Thanks for support
Currently i am work with VL53L0X in ble_uart_app example. it working fine , but its take 5ma current. How can i use TWI in low power...
Hi,
I would like to know if you can sniff BLE packets with really low transmission power, for example can you sniff a -35 db signal with any average bluetooth receiver?...
I've used PCA10040 sdk15.0 example ble_peripheral ble_app_uart
I can handle it through terminal.
If I insert strings through terminal, App can receive.
But, I...
hii,
i am trying to interface the nrf24LU1+ and nrf52832. I wanted to know if i can program the nrf24lu1+ without the requirement of nrfgo motherboard. or is it necessary...
