Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our customer is asking us to add Ethernet on board.
I want to use as much "off the shelf" stuff Nordic/Keil has provided as possible.
Is there a "typical solution" with...
Hi,
I'm trying to create to create A TCP/IP connection over Bluetooth between an n51x chip and other device (let say an iPhone mobile).
I've seen in the SoftDevice S130...
Hi I am using wireshark 1.10.6, when press 'w' wireshark started but it is not capturing packets. even I select my device then also facing same problem. I waited for some...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I'm still using SDK 12.3 on a nRF52840 product and am bashing my head against the wall because of issues with the USB driver. The current problem is all manner of hard faults...
Hello,
I have been trying to communicate via UART with the Nordic nRF52832 DK (10040) in a Linux (Fedora 26) Guest on Virtual Box. The guest is Windows 7.
The JLink...
I'm in the process of updating from SDK13 to SDK14. In the new CLI, there are a lot of NRF_CLI_VT100_CMD's that are used which weren't there before. If someone is using a...
Worked out of the box. The next day it would not turn ON. Tried charging with and without power switch ON. Charged from an Apple iphone brick and also from a computer USB...
Hi everyone,
I have moved from the cable connection firmware upgrade to the OTA-DFU using the nRF52 dev kit. I am able to download the firmware from nordic's website and...
51822/S130/SDK v12
I was testing prepared Write from iOS to 51822. Write Req/CMD can succeed, but Prepared Write failed with 'Unknown error code 0x82'.
What this 0x82...
I am design a very compact board for my project and running out of space. For this I am planning to replace two DCDC inductors with a single one. Is it possible to do this...
I am communicating with the nrf8001 via SPI, from an HCS08 MCU. First thing I receive:
0x01 0x04 0x81 0x02 0x00 0x02
This makes sense, it tells me it is in setup state...
In my design I am planning to power up some sensors from nRF52832 GPIOs. Is it possible to maintain the GPIO state high during the low power mode of MCU?
Please guide here...
Hello,
I have been testing the BLE multilink examples for the s120 softdevice. More specifically, I have tested the ble_app_hrs_c example in the experimental s120 folder...
