Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I am currently developing a HID device that supports BLE and USB. I have tested the firmware update function via both BLE and USB (USB CDC ACM). However, I am experiencing...
We aim to use an external Cellular module for MQTT communication.
I found that the nrfxlib/nrf_modem library is only supported for nRF9x series MCUs. Does this support...
Hi all, I'm trying to enable the SPIM4 peripheral on the dedicated high-speed pins (P0.08 SCK, P0.09 MISO, P0.10 MOSI, P0.11 CS) on the nRF5340DK, but I'm seeing no activity...
Been trying to set up a project to run some basic openthread as a proof of concept project. I based much of it off the CLI example and SDK. I have gotten stuck where my code...
Hi, I am using BMD-350-A-R module for a project and i am trying to upload the bootloader and the bootloader settings hex files but those are getting written as application...
Hi,
I am working with a u-blox EVK-NORA- B206 development kit. It has an onboard J-Link and it contains a NORA-B206-00B which has a NRF54L15 inside. I use VS Code with the...
Hi,
Could you provide some examples demonstrating how to use the FLPR on the nRF54L15 with NCS 3.2.1?
Additionally, real-world use case examples would be appreciated,...
Hello,
I am following this course: https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-3-bluetooth-le-connections/topic/blefund-lesson...
Hello,
Developing a new pcb with combined nRF9160, nRF5340 and nRF7000. We want to power the system with a nPM1300 PMIC. nRF9160_VDD on VSYS(4.5V), nRF9160_VDD_GPIO on VOUT2...
The Matter Samples output a verbose level of information to the console as standard. This is a mixture of the application log statements and matter log information. When trying...
Hello,
I am writing to ask a question regarding the power supply configuration when using an external board with the nRF5340DK.
I am referring to page 30 of the nRF5340DK...
Hi all
I have following problem. When using ble_nus_c_string_send to send data over NUS sd_ble_gattc_write returns error 19 - NRF_ERROR_RESOURCES after but the problem is...
Hi Nordicsemi engineers,
While testing a large-scale OpenThread network recently, I encountered an irregular pattern of device crashes. The network consists of 70 devices...
Hi,
I am working with NRF54L05 SoC using NRF Connect SDK V3.1.0 and NRF54L15DK for testing.
I am seeing an inconsistent MCUboot validation failure when flashing a firmware...
