Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello,
I have a Thingy:91x.
I flashed a BLE central program to the nRF5340 on this device.
However, I get an error initializing BLE. I've confirmed that this program...
Board/Setup:
Board: nRF9151 DK / nRF9151 SoC
Peripheral: External BLE module connected via UART1
Use case: BLE module is only needed during commissioning...
Hi there,
I have been trying to implement a low-power mode that basically suspends UART, I2C, etc before entering sys_poweroff() when critical battery level is triggered...
Hi,
I have several field devices using the LTE Link Controller library with nRF Connect SDK v2.5.1. Most of them work fine — they are programed to connect every hour. However...
Greeting Nordic Expert !
I would like to override the following hook in MCUboot:
int boot_perform_update_hook(int img_index, struct image_header *img_head, const struct...
Hello,
In the nRF52840 Product Specification PDF v1.11, on page 836, the second paragraph down states:
" The PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers and...
Hello Nordic team,
I’m using the nPM1300 development board to charge a 950 mAh Li-ion battery , and I’ve configured the charger as follows:
Charge current: 800 mA...
Hi,
I'm unable to get the PPKII kit to "connect" to my PC. After selecting the device it just says "Connecting..." forever. Some notes: - When first connecting the kit...
Hello,
I am trying to write a python script that performs a DFU on a nRF52840 so I can change its firmware without pressing any button. I think I have to use the pyusb...
Hello everyone,
I’m currently planning to develop an application that involves multiple Bluetooth devices operating within a certain range outdoors. Since there’s no option...
I’m developing an ESB-TX program using NCS v3.1.1 . Previously, I had developed an ESB-RX program using nRF SDK 17.0.2 . Now, when I use the TX code from the NCS SDK to communicate...
Hi,
I'm new to embedded development but have experience in desktop C/C++ development mostly with Visual Studio.
I'm struggling to get my head around how I would create...
Hello,
I am trying to define a pm_static.yml file which will use the 512K ram on the nrf7002dk_nrf5340 for the TFM ram section.
I cannot compile the non-secure nrf7002dk...
Hi, I got my nrf54L15 DK, but i can't start RTT logging. I set this configs:
CONFIG_PRINTK =y
CONFIG_CONSOLE =y
CONFIG_RTT_CONSOLE =y
CONFIG_UART_CONSOLE =n
CONFIG_USE_SEGGER_RTT...
