Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi, guys.
My first link was here https://devzone.nordicsemi.com/f/nordic-q-a/84673/building-sample-v1-8-0-zephyr-samples-application_development-out_of_tree_driver-gives...
Hello!!!! I use libuart to carry out DTM test. I start DTM test use follow codes:
after the codes executed, when i send data to device use libuart, it receive nothing...
Hello!
While looking at examples and trying to work on the nRF52832 with sdk 1.8.0 I am noticing there are varied uses of functions with and without the _dt at the end....
Case 1: Using nrf52832, solder bridge cut: what current values do the PPK gives : is it of the entire dev kit with all peripherals, programmer and BLE Soc or does it measure...
Hi, I'm attempting to migrate from SDK 14.2 to 15.2, and am encountering a problem with the crypto/rng module whilst trying to utilize micro_ecc.
(code being shown in order...
Soo,
I've had a sim and a device connected to the nrfcloud, it worked. Then I didn't use nrfcloud for a couple of months, and now it doesn't work anymore. It tries to connect...
I am using nrf52832 dev kit and soft device s132. I have use my board as peripheral
and i have another nrf52840 dev kit which i am using as a central connect it with my...
Hello,
I have to develop a new device that has to connect as a central device to three sensors, and has to connect as a peripheral to a smartphone. The type of connection...
Hi,
I'm observing a strange behavior with the UARTE peripherals on our nrf52840 based board when I'm trying to use a specific pin as TX.
In particular, I'm actually using...
Hello,
I've flashed to my custom nRF52832 board the ble_app_hrs_pca10040_s132 example, it works fine with iOS and Android hosts but when I try to connect to my development...
Hi Team
I have read https://devzone.nordicsemi.com/f/nordic-q-a/75801/request-tolerance-in-the-d-e-dimension-of-nrf52833-wlcsp . and https://devzone.nordicsemi.com/f/nordic...
The board is nRF5340 DK.
nRF Connect SDK1.8.0 / Windows
Example Peripheral UART.
I want to DECLARE them, not change them with different types of functions. There are...
We have given 1.8V supply voltage for nRF52840-QIAA in our application.
The following data is given in datasheet:
1) VDD,POR VDD supply voltage needed during power-on...
Hello,
I am having some build issues when attempting to add support for a Skyworks FEM to our application built with NCS 1.7.0 for a NRF52820 target. Our board file is...
HI All,
We are using NRF52832 for our project.
1) Can we wake up the NRF52832 chip from sleep mode using Bluetooth Event?
2) Can we wake up the NRF52832 chip from...
