I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I'm using nRF Connect for Windows with a PCA10040 DK to debug my nRF52832 product. Code is using SDK16 & S132
So I currently have one primary GATT service running with one...
I'm attempting to use the pc-ble-driver-py on Windows 10.
I successfully installed pc-ble-driver-py-0.11.4 using pip but when I go to run a Python script using it I get...
Hello,
I am looking at the ble_app_hids_keyboard example in SDK v17.0.2. Where can I find a table that will convert the letters on the keyboard to the hex values used in...
I have a Python script that I am wanting to use to flash our devices at manufacturing that uses pynrfjprog.
When running the script on Windows I get this error:
"FileNotFoundError...
Hi,
We have been working with a Zigbee coordinator, router and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS...
Hi nRF support team, By using the nRF Connect SDK, I am trying to implement an SPI communication with the display module from my nRF52840 dev kit and nRF52840 as a master...
Hi,
we have the need to implement the border router functionality for 6loWPAN in our device using a nRF52840.
Essentially we need to replace the Raspberry Pi in your examples...
Hi, everyone,
I'm trying to assign an SPI End Event to a DPPI channel on nRF5340dk to trigger a counter automatically. However, the value of the counter never increases...
Hi, I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1 (latest if I am right). nRF52840 DK as HW. I want to...
I need to collect data from approximately 20000 points. I want to form a BLE mesh network and collect the data. The sensors may be buried below the ground level about 30 to...
Hi all,
I have a problem with nRF52840 acting as TWI slave. I'm using TWIS. Typical scenario is:
1. Master writes request and ends transaction using stop condition.
...
Hi,
Scenario: 1 Thingy52 device and nRF52 Development kit is in a mesh network, where Development kit is connected to PC via usb cable and also connected to J-Link application...
With the release of SDK For Mesh v5.0.0 the mesh_stack_power_down() was introduced.
When calling mesh_stack_power_down() an assert was hit in nrf_mesh_timer_tail_handle...
Hi
I am using Mesh SDK v4.2.0 and I want to add Simple_On_Off Model to the Light_Switch example and provision and configure it with the provisioner example.
So far I have...
