Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi
I got it PPK2 and tested.
PPK2 is very useful compare to previous version PPK.
I wanted to sampling time expanding to 10min.
But i see that 2min time sampling...
Hello,
I would like to save some keys securely using the Infineon OPTIGA Trust X chip. To do a quick test I bought the Infineon shield2Go with the OPTIGA chip that I connected...
Hi All
as title.
I am nRF52 DK PCA10040.
Chip select is nRF52832.
I measure out from wfe to Timer Interrupt time is 1.3us.
Is it correct? and How can I reduce the...
Hello,
I am working on a school project with my team that requires one master device and up to 30 slave devices which will be controlling LEDs. I was thinking the nRF52840...
When enabling BLE on nrf52840, we are using specific API to access flash erase and write commands. All is working fine 99% of the time in term of read / write / erase into...
Hi Sir We are scanning nearest BLE using NRF Scanner example using 1- NRF52840-DK and 2. BT840 . We are getting good RSSI value using 1 but very poor RSSI values when we are...
Hi,
I am using nrf52832 with s132 softdevice and SDK17. I want to disable bonding and pairing in ble_multirole code. I have tried disabling the SEC_PARAMS_MITM, SEC_PARAMS_IO_CAPABILITIES...
Dear Sir,
I am using SPIM , EasyDMA array list,with following flags
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER , NRF_DRV_SPI_FLAG_RX_POSTINC , NRF_DRV_SPI_FLAG_HOLD_XFER&
...
Hi,
I am using my nrf52832 board with a MPC9808 sensor and I wanted to use the example code provided in zephyr/samples/sensor/mcp9808
Can you tell me with which pin of...
i'm building an amplifier that can play sound over bluetooth. I intend to use the nrf52832 to send i2s data to my dsp chip. based on the loopback example, i have an idea on...
Hello,
I was reading through the code of the asset tracker application and noticed that there is no while(1)/for(;;)-loop. I see this for the first time in a board application...
hello,
we are in process migrating to SDK 16.0 and service pack 8.27 or higher. While performing an upgrade we encourage few problems and would like you expert advise...
2 Questions, both short:
1. Documentation error in Softdevice 15.x and 14.x header files:
/** @note If any of the discovered services have 128-bit UUIDs which are not...
"AT+CEREG=2" "AT+CFUN=1"
Getting the correct responses of above mentioned AT commands.
But after that, when any command is send on LTE Socket, " at_host_at_socket_write...
