I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
I'm trying to devise the hardware platform for a Home Monitoring medical device. In the first place I planned to use the NORDIC nRF5340. With its large memory it would...
Hi.
We have a debug board for the NRF52832. The breadboard on this board is working fine. But if NRF52832 is used outside the debug board, then for some reason, some phones...
I want to set the Device's current date and time as I have to check time after certain interval. I don't want to use RTC where we have to look for ticks.
My questions...
Hello,
Could you please let me know if any of your devices would be suitable for our specific configuration?
We have a WMware server running many VMs. We would like to...
hello i am using nrf52832 and mpu6050 accelerometer with sdk 16 while programing i used 27 as scl and 26 as sda which is default in nrf52832 and i had no issues while reading...
Hi,
I am trying to test the light_lightness example present in ' nrf5_SDK_for_Mesh_v5.0.0_src' , on nRF52 Development kit(pca10040). And i am provisioning the device using...
I have a production device which I have soldered an SWD connection from a Keil project via the nrf51822 DK (port 20). I can flash code to this production device, but I cannot...
I'm using a SPI with a circular buffer so i need to have an interrupt with low latency that reset the RXD.PTR when the buffer is full.
The SPI is used for communicating...
Since Zephyr’s official BLE sample code, his BLE central only supports one central to one peripheral So I refer to the BLE central multulink officially provided by nordic...
HI ,
My name is MOHAMED ALI SAIDANE from Tunisia , i've been working on my project of the last year eduction , i'm interresting about the concept of the module NRF24l01...
We are using a custom ARM board which runs Linux and has a UART interface to a nRF9160.
I'm not how to phrase this exactly so I will just describe what I would like to do...
Hi,
I am using nrf51 DK and MDK is keil5
SDK : nRF5_SDK_12.3.0_d7731ad
softdevice : S130.
when i load the code nRF5_SDK_12.3.0_d7731ad\examples\peripheral\twi_sensor...
I have used light_Switch example from nrf mesh sdk nrf5_SDK_for_Mesh_v4.2.0_src I like to get the client source address in nrf_switch_server what should I need to modify to...
hello Nordic
i am using nrf 52840 dev kit, sdk 16.0
i want to make a sampling of 2 channels at 32MHz rate. the data shell be passed to RAM via easyDMA, after every 4...
