Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello, I am using nRF52840, SDK 16, SoftDevice s140 with SES. I want to configure my device first in connectable mode and then in non-connectable beacon mode. sys_advertising_init...
Hi,
The situation is very simple; I try to use the CoAP Utils library to simplify CoAP usage in an application running on the nRF9160 DK ( https://developer.nordicsemi...
Hello,
I’m using the ble_app_multirole_lesc application from SDK 16.0.0_98a08e2 as is (not modified) on 2 PCA10040 dev kits but unfortunetly both boards return a disconnection...
hi, nordic support
SDK version is 15.3.0
the example is ble_app_uart_c
I have modified the project based on this address: https://infocenter.nordicsemi.com/index.jsp...
Using nRF Connect SDK v2.1.0 and the nRF5340 PDK, are any of the ble mesh samples in the fw-nrfconnect-nrf repo working yet? I've tried both the mesh light and light_switch...
Hi community !
I wanted to know if it's possible to program a board as a client and as a server at the same time ?
Cause i want this card to send data into the network...
Using EmbeddedStudio_ARM_Nordic_v452_macos_x64
I am trying to build a sample for 9160-DK
In nRF Connect Options I entered:
Board directory ~/src/ncs/zephyr/boards/arm...
I am attempting to build the latest (4.1.1) pc-ble-driver with 115k2 baudrate. I have a hardware platform which supports 115k2 as maximum baud rate. It seems only the 1m version...
Hi,
I am using the NRF52840 with the usbd_ble_uart example using the latest SDK.nRF5SDK160098a08e2.
My computer (windows 7) recognize the NRF52840 as a nRF52 USB CDC...
Hi. twi_sensor As an example source, I have 2 pressure sensors. I use sdp800 and icp10101 separately and use it as twi_interface to read the sensor value well. However, we...
If I write the data from NrfConnect App and if I again go to the scanner tab without clicking on disconnect or killing the app and then if I click scan or refresh option,...
I want to transfer files to uart using ymodem protcol.
For example, when nRF52840 receives a file through BLE,
it tries to send the file back to the device connected to...
Is there a sure fire way to know for sure that my PSM configuration is correct on the nrf9160DK? I'm trying to get LTE-M + GPS working and I'm still not sure if I'm in PSM...
Hello,
We used the Nrf52810 in our project.
Currently, we found a issue: The ble is disconnected when we press the chip. Because our buttons are on top of the chip. We...
When I use circuit configuration no.5, VDD connected to VDDH and have 5V going into VBUS, I see a 1.6V output from the VDD_nRF (VDD/VDDH).
Normally when I connect a battery...