Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
Hello
I am contacting you because I have 2 problems:
1. I downloaded the "nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b" available at this address: www.nordicsemi.com...
Hi!
I'm using nrf52832, SDK 16 and s132. I've successfully used a ble_app_hids_keyboard example to make a Bluetooth HID peripheral device to transfer sensor data to the...
I want to use a timer to generate an event at a rate of 16kHz. So just as a test I'm setting up TIMER4 and a CC event to toggle a gpio pin. As I understand the clock source...
Hello everyone,
I set up Thread Secure OTA DFU Example by using a nrf52840 DK as DFU server and a nrf52840 Dongle as DFU client. I am using nRF5 SDK for Thread and Zigbee...
I'd be grateful for some assistance with what I may be doing wrong.
I have programmed the serial example on a device and the server example on another device.
Copied the...
Hi everyone:
I was testing the bonding with passkey entry, but it seems failed.
The slave 51822 EVK board is set with "BLE_GAP_IO_CAPS_DISPLAY_ONLY" and "MITM = 1".
...
Hello devzone! I am using translation.
I am using a DK board (PCA10056) to examine the current consumption of nRF52840. I commented out the advertising_start() of the SDK...
Hi, I'm trying to implement a mesh serial node with LPN capability, where the UART can be disabled to save power, and then re-enabled via a GPIO.
I am measuring current...
Ok -
I've been through this a few times and read the forums, but the current build system is broken. I'm trying to compile (not even load the board at this point) the ble_hts...
Whichever input channel I select, I always get a value close to zero. Here is my test code using VDD as the input source:
In this case, RTT reports that the value...
More of a plea than a problem. When I migrate to a new version of the SDK I try to be very careful. So, I use sha256sum to check all similarly named files from one version...
Hi,
I am trying to read the SFDP (Serial Flash Discovery Parameter) register of a Micron NOR flash memory using nRF52840 QSPI peripheral. The read SFDP register op code...
Hello,
i work on nrf9160 dk
I would like to know if it is possible to use an AT firmware to be able to easily switch to LTE-M, NB-IOT, send sms, switch off the modem...
Hi.
I am using nRF52840 & SDK 15.0.0.
I set the advertising slow timeout to 14 min, But, the advertising stops at about 3 min.
The followings is summary of advertising...
