Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi I noticed that all of the examples use common/src/app_level.c Why is that? Is it recommended to not implement your own generic_level callback for example?
Hello,
I was downloading a project to the flash memory using J-Link SDK and I am having this messsage:
JLink info: ------------ DLL: V6.80a, compiled May 29 2020 16:27...
Hi,
I tried connecting the thingy91 out of the box and it was working fine, sending data to nrfCloud.
Now I tried to build the asset tracker application on my own and...
Hi All,
I am facing the issue with sleep current in nrf51822. initially i checked the sleep current 11uA. but after one hour it is increasing to up to 390 uA gradually....
Hi All,
I am currently designing a BLE module using nRF52840 chip which works with battery.
In the nRF52840 DK, it uses a Power Switch Driver ( SC728CSTRT ) from Semtech...
I want to add a button function to the ble_app_uart.
I don't need to use the functions of the BLE Button Module.
It's enough to just change the value of the variable when...
Hello,
I'm trying to develop a small module based around the nrf52832 chip, and I am trying to replicate the reference design and layout as closely as possible. One problem...
Hello,
I am updating my application from older SDK 15.0 to use SDK 17.0.
NRFX_NFCT_ENABLED NRFX_CLOCK_ENABLED are used to enable the files nrfx_nfct.c, nrfx_clock.c respectively...
Hello DevZone,
I am developing a system that has a SoftDevice, UART bootloader, and application. The SoftDevice is S132 SoftDevice v6.1.1. The UART bootloader and application...
RTT seems to be mostly working using the viewer with the command:
JLinkRTTViewer -device nRF52840_xxAA
It seems I need to re-connect each time I start a debug from SES...
Hello Nordic
We are in the process of product development and at the moment we need a chip that transmits stereo audio to any BT headset. That it is possible to control...
I am using nRF52840 as a master to communicate with esp32. For esp32 i am using arduino ide and esp 32 slave library( available in library manager of arduino ide).
For nRF52840...
Hello,
I use nrf52832 with 65 kb RAM.
I can't understand why soft device takes about 30k RAM memory.
I see "reserved_ram" has 30k.
Can I change size for 20k for...
We're using the nRF52840 on a battery-powered device that requires very low power consumption, both in run mode and also in the Cortex-M4 sleep / deep sleep modes. We've recently...
