Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi, I've began making a SPI module for programming a PIC16. It only transmits data, so two pins. My questions are: 1. any obvious errors? 2. does the EVENTS_ENDTX occur when...
Hello everyone
I have an question when I used the 52832.
First of all,I configed "nrf_drv_spi_init(&spi, &spi_config, spi_event_handler, NULL);" and the file (nrf_drv_spi...
We are about to use the nRF52832 and are looking at which SofDevice to select for a Central-only implementation. The S122 summary says it targets the nRF52820 and nRF52833...
i m using NRF52840 with sdk 15.2. In that i m testing direct test mode by UART.Now i can do transmit mode.i can check through nrfconnect dtm mode. i cannot check receiver...
Hi,
I tried the following AT settings on the nRF9160 DK board:
AT+CPSMS=1,,,"00111000","00011110"
AT+CFUN=1
After this the modem enters PSM mode and the current is...
Hi,
One of our modules using PCA10090 0.8.2 programming and production nRF9160/nRF52840 modules.
Our customer reported that they can't use PCA10090 0.9.0 re-programming...
Hi! I ran into a little misunderstanding in setting up clock frequency for PDM. I need to work with lower clock frequency than default - 0.64 MHz. I see, that PDM_CLK = 32...
Hi,
Some questions on the scan consumption of nRF52840 and using the attached Online Power Profiler for BLE as reference
If I am using my nRF52840 to scan 24hours at...
I wish to merge the cloud_client example with GPS example. How should I go about it? Along with main.c files of both, which other files will I need to merge?
I am currently making a program that will interpret serial commands from UARTE1 and then send + read something from the other (UARTE0). Previously, when I have been using...
Hello,
I want to be able to send 1 MB of data from a server node to a client node
I have made a simple model with an array that holds 300 bytes.
and upon a timer the...
Hi,
I want to connect Multi peripherals to one central and want to send the device name(peripheral which is connected) through the uart.
How do i get the device name which...
I have seen some variations of this issue but hoping someone can lead me in the right direction.
Similar to others, I am using NRF_LOG_INFO for debug messages. It works...
Hello, I am working on a project which uses nrf52832 module ( https://www.seeedstudio.com/MDBT42Q-nRF52832-based-BLE-module.html ). I just want someone to review its circuit...
