Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi,
I have been working with different boards to implement different ML TensorFlow Lite samples in the 52840. I used Particle and Arduino BLE Sense.
All forks from the...
Hello,
I have programmed Fanstel BC832 module with S132 and ble_app_blinky example successfully and I can see the advertisement of BC832 on nRF Connect app. The thing is...
Hi,
I am trying to render some chinese strings on an OLED display. For this I would like to concatenate some strings using swprintf.
But when the replacement string contains...
Hi,
I am trying to flash my nrf52840 dongle via nrfconnect, but it doesn't work.
My project is based on BlueTooth and ZigBee connectivities, so I opened the programmer...
Hi there
I am currently trying to wakeup from system On mode using the DETECT signal and Port Event.
According to the product specification:
Trying to put the system...
Hello,
I'm using zephyr logging APIs to print to serial port. If I log too quickly the output is not correct. Running the code below I get
[00:00:00.626,464] <inf>[00...
Hi,
I am developing a new design using your nRF9160(using LTE ONLY targeted for the US /FCC) + NRF52840 ( using BLE ONLY)
I have noticed that in both the reference designs...
Hi,
We are using NRF52840 in our project. Here my doubt is we need to read the voltage from the sensor which will vary from 0 to 5 v .Can you plz tell me which example program...
Hi, I added the SAADC feature to a beacon project so I can measure the battery voltage. Interesting thing is that my readings always show around 100mV less then VDD voltage...
We are developing a small BLE device and want to make sure we follow reasonable security standards. What type of communication security would a typical device like headphones...
Hi,
I want to change the pin configuration for the uart2. I change it in the SES 's Project>Edit Device Tree .
However, if I change the tx pin to 0x0f , it cannot send...
Hello, Is there any NFC sample for Thingy:91 . I need to connect a device to Thingy:91 using NFC for a project. I am using v1.1.0 tag of ncs repo.To understand how NFC libraries...
I need to set REGOUT0 to 3v3 for a custom board. What's the best way to do this using the armgcc toolchain? Right now, I'm setting the value first thing in my main:
Is...
Hi,
I try to write some data into the flash memory, but I always get a hardfault when I try to use the write function provided from the examples:
No I think this...
