In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
In the nRF52840 Product Specification v1.1 ( HTML ) , description of the QDEC peripheral, Table 77 on page 275 ( direct content link) , it appears to indicate that the LED...
Hi,
We have an freertos based app (SDK14.2).
Recently we have added a WDT support in the following manner:
The init code initializes the WDT reload value to T+3...
hi all, i am using the uart with it's dma to transfer data into the nrf9160, but some of the data is lost in it's way. here are some examples of the loss count in bytes from...
Hello,
I'm using several nRF52840 boards to setup a bluetooth mesh network. Im using the python script "interactive_pyaci.py" to setup the mesh. The mesh is working and...
Hi, As the title asks, I am using the lte_ble_gateway example project on the nRF9160 DK. I am able to connect one nRF52840 DK to the nRF9160 DK over BLE. I am trying to connect...
We have a board that has become unresponsive to programming. It worked well to program about 4 times and then is no longer responding to the J-Link device. The application...
Hi,
I tried implementing serial communication between nrf52832 and HT1632.It didnt work.In HT1632 data sheet it has given following specifications
will nrf52832 supports...
I am trying to build the simplest nRF52 BLE Peripheral application (Lightbulb use case). I am facing below mentioned errors:
Building ‘ble_lightbulb’ from solution ‘ble_lightbulb_pca10040_s132...
Dear all,
I'd like to use 2 spi and 1 i2c at the same time. Can nrf52 support? I read some thread said that only using 1 spi and i2c or 2 spi. Please advice.
regards...
I'm using SAADC like this:
And I'm not getting the done event. I've also tried not low power mode.
If I place a breakpoint in nrfx_saadc.c nrfx_saadc_irq_handler, after...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK , and I'm trying to print floats using vsnprintf (I'm guessing the problem is the same as with...
Hi,
We are using nRF52 DK tool to sniff BLE data. We we using Wireshark plugin to interface nRF52 DK tool. nRF52 is updated with latest firmware. We keep the tool in between...
Hi,
we are porting code of our project from SDK 14.2 to SDK 15.3.0, and have encountered unexpected behavior from the fstorage module. Even though SoftDevice and BLE stack...
I'm trying to work with the PC-BLE-Driver with the connectivity firmware. I've loaded the connectivty firmware and the application appears to connect to the board. But I'm...
