Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello,
I recently switched to linux and I have many problems since then.. So I noticed that printf functions are not working fine for me e.g. in ble_peripheral_uart example...
I've worked with other integrated radio + ARM processors that were not deterministic, and I would like to know if the Nordic solution is.
What I mean is: Is there a way...
Hello all,
How does the handling of ble events work with SDK 15.1? When I register more than one event handler with the macro NRF_SDH_BLE_OBSERVER(), how does the softdevice...
Hello Support team,
I'm working on a project where I am designing a custom board uisng the Nordic NRF52840 as the MCU (forgive me if I'm using the incorrect terminology...
Hi,
I am relatively new to programming hardware at this level, and have developed our product on the 52832, so finally I have purchased the Power Profiler Kit, and downloaded...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
hello
I am currently trying to use the thingy_52_sdk sample code to embed a program using the J-link debugger with the Nordic thingy 52 development kit. But the build is...
Hello,
I am attempting to test slew of Rigado BMD-350 module BLE radios (uses nRF52832) using a Rigado BMD-301 series Eval Kit to act as the central. The BMD-350 device...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132. In the ble_peripheral / ble_app_uart example you can only connect through the...
If followed the following steps:
Installed Win10Pcap
Installed Wireshark-win64-2.63 on Windows 10.
Using nrfGo Studio loaded sniffer_pca10040_51296aa.hex (after erasing...
Hello fellow Nordic Community,
We have a usecase in which it would be beneficial with a tx power of - 30 dBm . This is a value that was supported with the nRF51 chip series...
Hi,
I am develop a project with dfu and bond features. I found that in dfu project, IS_SRVC_CHANGED_CHARACT_PRESENT is always set to 1. In my understanding, if set this to...
hi,
i am using Nordic thingy:52 with a nRF52840 with s140 softdevice to receive multiple characteristic data from thingy like thingy environment service have 6 characteristics...
Hi,
Is there any way to stop the OTA DFU? Let's say that I started it and at some point I want to cancel the process at 40%. Is there any way to send a control message to...
Hello fellow developers need your help
I have bought 3 nRF52840 dongles and want to setup a mesh network as stated above. I have downloaded nRF Connect windows application...
