Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I can use standard UUIDs and successfully add a Service and several characteristics, so I think the error message above is a red herring. When I attempt to create a custom...
Hi there,
I am trying to modify flashwrtire peripheral example code for uart bootloader,
- I have used flash read write softdevice functions (sd_flash_read/sd_flash_write...
I am trying to program a BMD-300 over a serial connection through the RigDFU bootloader. The module has been updated to the latest factory image.
I can compile the application...
Now I want to run the python scripts interactive_pyaci.py in Embedded system device, I want to know which version of Python Environment must be install in the Embedded device...
I cannot find the call to sd_ble_gap_appearance_set(...) function in the ble_app_blinky example, so that I think it's unnecessary to call:
in nRF5_SDK_for_Thread_v0.11...
Hi!
I am using UART in NRF52832 with SDK15.0.0 to communicate with TCP socket via cellular modem.
I am using printf() to send the following AT command sequence to the...
Hi, I am using the Serial port library in SDK15. I am using the port in NRF_SERIAL_MODE_IRQ mode. After transmission the number of bytes receive are variable ranging from...
Hello. Im working with:
sdk14.2
softdevie ANT_s332_nrf52_5.0.0
chip: nrf52832
Problem: we have a product almost ready to be sold. We decided to start the migration...
Hello. I am trying using the nRF52832 with SoftDevice S132 v4.0.2 and SDK v13.0.0 along with the uECC.c/h files that I downloaded from github.com/.../micro-ecc . My device...
I know you can configure the threshold for low voltage that would stop writing to flash.
some people set this to 2.7 volts.
I want to know what the minimum voltage the...
I have followed the exact steps mentioned here http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v2.0.1%2Fmd_scripts_interactive_pyaci_doc_demo_configuration...
Hi all
I use nRf52840 with SDK 15.0. It allows SPI SPIS and TWI (i2c) ,but almost 3 items in the same time. I want to use spi0 as master to configurate my other mcu and...
Hi everyone!
I'm trying to write demo application to evaluate how custom services would work on nRF52840 SoC. Problem is that iPhone ( iOS 10 and iOS 11 ) doesn't show device...
