How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello,
I want to create a small BT Mesh network to demonstrate the possibilities and advantages of BT mesh, for example switching on two lights via BT mesh, collect sensor...
I wan to network multiple avr microcontrollers with nrf240L1+. My project is 2 0r 3 seprate microcontrollers read tempreature from their sensors and send them to a base micro...
hai, i am using sdk-v-12.3.0 for nrf52832-pca10040,
I connected the SOC to PC using Daplink.Now,i want to just print "hello world " on the /dev/ttyACM0.could any one please...
I am currently working with a custom board that captures an ECG using an AD8233 chip from analog devices. Attached to the board are gold plated pads that act as electrodes...
Hi
Does nrf52840 PD Kit support development of ble 4.2 standard applications? If yes, how can this be achieved.
NB: I have 3 nrf52840 PDKs and wanted to use them for throughput...
Nordic Team,
We are using Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v3.0 to sniff packets from BLE 4.0 device - but we are finding it hard to connect...
Hello ,
i use blinky example from C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001 folder. I want to flash the led with periods (period of 30 ms turn on 10 ms off) ...
Hi,
I'm using 52810 basing on ble_app_uart example. We use a IO to start or stop advertising. Start advertising w hen the IO level is low while stop advertising w hen the...
I use SMK BTS-04 using nrf 52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command...
I use SMK BTS-04 using nrf 52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command...
I am considering using two nRF52832 or nRF51822 's for a project which requires two way BLE communication. Pressing a button on one end should cause an event on the other...
Hello, I have an adafruit bluefruit feather m0 which has nRF51822 on it, I was able to establish a connection and send data until yesterday. When I try to find my adafruit...
Hi All,
I have a general question about the FreeRTOS implementation for SDK 14.0.0.
I've added FreeRTOS onto a basic UART BLE peripheral example that I wrote. I referenced...
