I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
In this application, I tried to enter a wrong bonding passkey to test PM_EVT_CONN_SEC_FAILED case. But I found that the program went into this case and after executed "sd_ble_gap_disconnect...
We developed a new BLE hardware product using the Laird BL652 third party module. Our product is based on the latest Softdevice S132 V5.0.0.
Now I'm starting the Bluetooth...
I have problems getting the beacon example in the new mesh SDK v0.10.0 working.
I invoke cmake with this command:
cmake -DTOOLCHAIN=gccarmemb -DPLATFORM=nrf51422_xxAC...
Hi there~. This is Matthew! I saw a thread explaining that the production variants of the nRF52840 will first be available Q4 2017 at this link .
I was planning for BLE...
Hi,
I had a difficult problem.
First, S110 & SDK9
ble_stack_init () is the source.
static void ble_stack_init(void)
{
uint32_t err_code;
// Initialize the...
Hi. I'm using nRF51822 as Peripheral.
To init the service for example "NUS", i have to call NUS_BASE_UUID as below..
#define NUS_BASE_UUID {{0x9E, 0xCA, 0xDC, 0x24, 0x0E...
Hey guys,
From what I understand, the minimum connection interval on say, an iPhone, is 20ms. Also, you can send up to 6 packets of 20 bytes within a connection interval...
I have established a ble connection between two dk boards, the code I based on is the ble_app_uart_c and ble_app_uart, and try to detect some rising edge delivered from the...
It's kind of relative question with my previous question.
"When smartphone range is shorter than a peripheral(nRF5X), is there any way to receive an advertisement from the...
Hi all, I tested the example: Experimental: LE Secure Connections Multirole Example with my smartphone and it is working fine, but when I tried use LESC on my peripheral device...
I can't open a com port after starting the nRF Connect app. This happens in Windows (native) and also a Linux virtual host with the com port passed through. I'm using a nRF51...
I found strange behavior when using back-to-back packet transmission.
Configuration of PTX/PRX is:
No Auto-ACK (disabled)
CRC 2 bytes
Packet length 13 bytes
Addr...
I have the blinky examples working, but have not been able to get any example code using any gpio input to work. they compile fine but the buttons done seem to work. I'm using...
Hello,
I'm using the sample project from this post .
Following the steps and using nRF52DK, one for server and one for client. I've modified the server count from 3...
