In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I want to implement FOTA Update for a nrf5340 based board by using nrfConnect SDK v2.9.0 with zephyr and mcuboot. The board has a MX25R6435F external flash (same as the nrf5340dk...
Hello,
I am trying to run a ztest integration example I found under this one here: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/subsys/testsuite/integration...
Hi,
I am sending out same payload through ADV packet and BLE connection packet, I notice the ADV consume more power compared to connection one,which is quite strange.
...
Hi, I am using NRF connect sdk 2.6.1 and I am wondering what is the best way to run crypto operations when using TFM profile type minimal and building for nrf9160_ns. TFM_PROFILE_TYPE_NOT_SET...
I want to measure the current consumption on the DK with an Amperemeter. For that i have this setup:
Please excuse my terrible drawing skills. Im basically powering...
I am using NRF52810 as a beacon tag.
I want to apply AOA technology to this tag, is it possible?
I'm confused because the nrf52810 says it supports BLE 5.2.
Hi,
I'm experiencing memory constraints while using the nRF52811 with the SoftDevice S112, as it takes up a significant portion of the available memory. Is there a lightweight...
Hi,
We developed an application on the nRF52833 and are now porting it to the nRF54L15. As part of this process, I'm integrating an external RTC via I2C on the nRF54L15DK...
After purchasing the PPK2, I connected the Fluke287 and PPK2 Ampere meter in series to check whether the measured values matched the Fluke equipment.
The Fluke287 consistently...
Hi
I have run nrf5340 WiFi shell project in ncs2.9.0, everything ok if use Logging UART0 for cmmands(wifi scan/wifi status/ wifi connect.....etc)
now I need to use...
Hello all,
I have slightly modified the coap_client sample from the SDK such that the main function is being called on certain actions from another program. I'm getting...
I use the gpio8 interrupt to detect whether the SD card is inserted. When a falling edge is generated, it means that the SD card is inserted. But I found that sometimes, the...
So I have been doing a project on nrf52840dk, So I have built a custom bootloader for it as well, I have been trying to add the custom bootloader with the code in my nrf52840dongle...
Hello,
I have a question about the NRF SDK fundamental lesson 8 exercise 1. In the code below get_access and release_access are executed in different threads. The semaphore...
