Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi, I am currently evaluating a Rust driver for the nrf7002-ek on a nrf5340-dk. I have been using the Zephyr nrfwifi driver for reference.
There are a large number of nrf_wifi_fmac...
When building a project using a custom board, as well as both the b0 and mcuboot bootloaders enabled, board-specific child image configuration causes the build system to ignore...
Hi All, I am looking for assistance with trying to reduce flash usage of my project. I am using NCS v2.6 with an nRF52832. Attached is my prj.conf file. The major SDK features...
Hello, I'm working on a Zigbee application using the nRF5 SDK for Thread and Zigbee v4.2.0. The app builds fine, but when running it I get the following output:
I have...
Hi All,
We are developing a heater controller using Nordic Matter Thermostat sample code. The sample code has following value.
Off
Heating set point
Cooling set...
Hi,
I use 3 devices in the Mesh application. I am looking at the Mesh:chat example. I want this,
I want to press a button on one device and light LED1 on other devices...
With nrf52840 we have different protocols to add as per application. but is it possible to include following for single application in single hex? 1) zigbee: coordinator,...
Hi
I'm testing downloading a file from AWS S3 using ncs but it's not working well. I'm getting an error called -116 Connection timed out. I also used another client to connect...
I am trying to split the external memory into littlefs storage and mcuboot secondary slot. But I'm not sure what I'm doing right
pm_static.yml
board_file.dts
Hello everyone I am using nrf5340 with sdk ncs v2.4.2, I broadcast BLE and there is a situation where it is stuck and cannot be controlled or do anything, but I can still...
I am working with an nrf9161 and I can see that the IMEI is not programmed and likely causing my connection issue. I only have the modem connected to an rtt and nrf5340 what...
Hello community,
I am developing a device that uses the NB-IoT network . I would like to know if the NB-IoT module of the nRF9160 supports SMS . If it does, will it provide...
Dear Ladies and Gentlemen,
We have recently started comparing the BM833 (and the corresponding nordic devkit nrf52840) with an other hardware (ESP32), neither uses amplified...
Hello everyone,
please take a look at my minimal reproducable example, which explains the problem and also includes some example measurements. derteufelqwe/nrf-ble-datarate...
