Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi，
Please help me with this interrupt error
dk:PCA10095 0.11.0
sdk：ncs v1.5.0
example path:D:\ncs\v1.5.0\applications\2_hello_world_timer
example code:
test...
Hello, I have a big problem now. I set up a BLE network with 11 peripheral boards connected to 1 central board via NUS protocol. the peripheral board is based on NRF52840...
We are making a product with nRF51822;Powered by a CR2032 button battery ； Hope to achieve low power consumption;
It can be seen in the datasheet that nRF51822 has Internal...
I've been checking the nRF52805 Errata document to see which errata apply to our product and do not yet have a workaround implemented in our firmware.
Unfortunately, I'm...
Hi,
Device FW information is as follows: SoftDevice: s113_nrf52_7.0.1_softdevice.hex bootloader: mesh_bootloader_serial_gccarmemb_nrf52832_xxAA.hex device page: device_page_nrf52832_xxAA_s113_7...
I want to use our app in phone to communicate a nrf5340 board through ble. my project use sample peripheral_uart . but app ble three 128 bit UUID is different from ncs1.5...
Hi,
I'm trying to measure and log the low power coming from a peltier module. (TEG seebeck effect). In Ampere meter mode with LED for load I get nothing. Replace TEG with...
Hi,
I successful developed a application using nrf / zephyr SDK and install the applications on the nrf52840dk and dongle. Now I want to adjust the power using
CONFIG_BT_CTLR_TX_PWR_PLUS_3...
hello i am trying to interface RN8209c ic with nrf52832 using uart communication with sdk 15.2
uint8_t readbuf[50];
uint32_t err_code;
uint8_t buf[10]; buf[0]=0x7f;...
Hi,
I am trying to modify the Android nRF Mesh app to filter un-provisioned devices with URI hash contained on un-provisioned device beacon.
My question is how I can...
Hi
I have a question, the Nordic SDK have a DFU, I want to know what is the default value of TX power in Bootloader? Can we change the TX power? if yes. How to change it...
Hello, I'm using nrf52805. It is confirmed that P0.04 is AIN2 and P0.05 is AIN3. Can I use this pin as UART TX,RX? What should I do to use it? Thank you.
Hi!
I am trying to work through the nRF Connect SDK tutorial series, and I got stuck at the "building with west step" in part1.
When I try to build my project using the...
