I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi all,
I need to use the SPI3M interface and following various example I implemented the following code on the nRF52840 with SDK 3.0.2
Whenever I configure the SPI to...
Hello - Just download and installed NRF Connect for Desktop 5.2.0 on Windows 10. Trying to Quick Connect to new PPK2 1.1.1.
When I plug in USB Quick Connect sees the PPK...
Hello,
we were using the mcumr_flutter 0.4.2 library to Update our NRF54L10 over the air with an app. This was working fine using the nRF Connect SDK Toolchain v2.9.0. However...
Hello,
I'd like to have the gcc linker calculate a checksum over a specific address range (defined in .ld file) and store that checksum at a specific address (defined...
example: peripheral nus device: nrf52832(Self-developed board) hi i run the example peripheral_nus , but it cannot work. Though i had set the RC clock. But when i run the...
Hi, I am developing a product that has a nRF52840 as the main MCU and it controls a Quectel BG95 (a LTE-M/NB-IoT module, powered by Qualcomm's 9205 LTE modem) using Zephyr...
Good Day,
Im a developer in switzerland using the nrf9160 trying to connect to the nrf cloud using mqtt, i have already flashed the credentials, updated the modems firmware...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi all,
In Device Manager, my nRF52840 DK is recognized as follows:
JLink CDC UART Port (COM32) JLink CDC UART Port (COM33) USB Serial Device (COM22) — running a Zephyr...
I'm looking to use the new Zephyr support for the ProMicro nRF52840 board, which appears to be available in NCS v3.
However, Zigbee R23 only appears to target v2.9.0.
...
Dear devzone support,
I have a quick quesiton.
Why does the nrf5340_audio application only support 1 BIG, while the nrf_auraconfig support 2 BIG. Is it because of using...
Hello,
I'm adding power management to a custom driver that talks to a sensor via uart2 of the nRF9151DK. But from my tests it seems that uart_irq_rx_enable() has no effect...
Hi all,
I've got an existing OpenThread project for my workplace's metering product which currently is written for a TI CC2538 and I'm porting it across to run on a nRF52840...
Hi, I have a custom board with nrf54l15 and it does not have a 32 kHz crystal, it only has a 32 MHz crystal. Sometimes the code gets stuck at this line: Can it be related...
I have a peripheral which has an nRF53. It connects to either an Android of iOS phone. I've been testing add Connection Subrating. However I've been noticing that the Connection...
