I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I want to add some logging to my nrf5340 net application and I'm having some troubles.
I have the following in my main.c: #include <logging/log.h> LOG_MODULE_REGISTER...
Its clear there is little interest in this DK compared to the nRF52 version. I got instructions for that platform that actually worked.
Not so for the nRF51 DK. But I am...
I am using FreeRTOS and some of the commands there have two flavors: for using in regular code flow and when are executed from an ISR, but in nRF SDK components and examples...
Hi All,
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer.
My setup: HW: PCA10040 SDK: 17.0.2 Project: nRF5_SDK_17.0.2_d674dde...
Hi,
I followed all the steps to get NCS up and running with SEGGER Embedded Studio. However, when I try to open an example, I get this error:
Including boilerplate ...
Hi all,
I am currently working with nRF52832 boards, and I am trying to save some values in my flash memory. I have already created a code for this purpose and I am able...
Hi, I'm currently trying to understand multi-Link and Immediate Alert Server Application (ias) examples in SDK 17.
While I'm analyzing them, I got some questions:
Q1)...
Hi,
I am working on the nRF52832 ,why i can't able to set the low 7.5 ms interval . I am getting the error at ble_advertising_start . Do I want to change anything else?...
We are preparing our nRF52 product for the unintentional radiator test. Currently, the SoftDevice is enabled and we have the low power mode disabled with the following changes...
Hi,
Looking for some guidance on how to use the 'cryptographically secure random number generator' in a Zephyr/nRF Connect SDK application on an 52840
Is this a supported...
Hi sometimes it happen with my nrf52832 based device. The common way I am programming firmware during development is next:
nrfjprog --program fw.hex --sectorerase --verify...
Hi,
I am working on the nRF52832 ,If i want my data to be transmit every 7.5ms then what should I set the minimum connection interval and maximum connection interval ? please...
Regarding that the nrf52811 is able to use direction finding, there is any example for configure a tag with the nrf52811 to be located? Did nordic finally release any AoA...
Hello,
Sorry if it will be long. thanks for the help.
Using nrf9160 dk. The first thing I want to ask is about is the pins. I want to make sure I am using the correct...
Hi
I am currently using nrf52840dk with zephyr, and SPI used to work fine.
Now, as a slave, the kit only reads the data read while MISO is high (this might be what's supposed...
