I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hi,
Is it possible to add other, optional data pages to ANT+ BPWR profile? For example page 0x13 (Torque effectiveness and pedal smoothness)?
Thanks,
Pepam
Hi NRF Team,
My Configuration:
NRF51822
S130
SDK 12.2
I am using multiple application timers in my project. Most of the cases timers has to run concurrently. Lets...
Hi Team,
we are using the nRF52840 for our development purpose. we need sample code for Stack overflows/under flow and Memory leaks detection in runtime by using MPU....
Hello,
I have a central and Peripheral beacon on nrf52832. I am usıng nus services on both devices. After the data transfer I call the
ıt works fluently on the central...
I have been using CrossWorks for a while for multiple vendors MCUs (sometimes in the same project on the same PCB). I'm looking at using nRF Connect SDK and see that SES is...
I'm using SEGGER Embedded Studio with nRF5 SDK v16.0.0.
For the purpose of high-speed data transfer, I've searched about the BLE throughput.
Now, I want to figure out...
Hello
PWM and I2C are being used on a custom board using nrf52832. I connected I2C to pins 26 and 25 and PWM to pins 27. But I2C doesn't work, and PWM does, but there's...
Hello,
I search a NORDIC example (RF52832) that is bonded with a battery CR2032 as power supply runs very long (> 1 year).
Bonded with whitelist
Bonded with one or...
Hello,
I want to create/compile a (Nordic) secure bootloader with serial output.
I know the example of the dfu secure_bootloader. I also know there is a nomal and a debug...
I am using NRF Connect SDK on NRF52840 Dongle and I have written two programs. First acts as bluetooth peripherial device, second acts as bluetooth centeral devices. I have...
Hello! So I'm working on a project where I try to connect the nRF9160 DK to the google cloud. I tried to manage this by following this guide: https://devzone.nordicsemi.com...
Hi,
I'm using the BLE app (ver 3.6.0) in nRF Connect for Desktop together with a PCA10056.
I'm scanning for a device that sends three ADV_EXT_IND, one on each channel...
Hi,
I am using the USB CDC example in my project, where I developed my own application level communication protocol.
I have a problem with the data throughput, it's...
I am designing a custom board with a nRF52840 module that has no 32.768 kHz crystal embedded in it and as a first step want to test it with some examples that use only RC...
Hi all,
I'm trying to setup an interrupt-driven UART. UART is able to transmit data, but I don't get the TXRDY interrupt.
Below is my minimal initialisation that outputs...
