Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi,
I'm working on sending reliable message from server to client. It totally works fine if the message is less than 24 Bytes but then I got error when it's larger. The...
Hi, i am trying to add on_adv_evt in ble_app_beacon example. I modified sd_ble_gap_adv_set_configure(& m_adv_handle , &m_adv_data, &m_adv_params) to sd_ble_gap_adv_set_configure...
Hi, we are using nRF9160 and would like to save a data that is written only once(should not be overwritten or erased) and accessed every time it starts. I found that flash...
If LESC is not possible I'll settle for legacy.
I'm not able to find any document or sample code to help me get started. What i need is a pointer to document and hopefully...
Hi
I want to run the serial_uartes example for pca10040, are there any changes that i need to make in pca10056 config ? or will it work as it is in pca10056 ?
I am using...
Hi,
i am working with nRF52840-DK which i received yesterday from shipment. so i want to eun the BLE peripheral application on that.
As we know if we want to run the BLE...
I see this quote in response to a question asking for examples on how to code a scan response
possibly not - but it's trivial - just encode the scan response in the same...
Hello,
I am using SES V4.5, SDK 15.2 and the "ble_app_blinky_c" and I was not able to see the programme log.
I tried setting up the file "sdk_config.h" to use the RTT...
Hello,
I'm starting to develop an application using the DK pca10040 and SDK 15.3. At first I have just adapted peripheral ble_app_uart example and incorporated fds functionality...
Hi,
This may be a simple question, but I've gone through the infocenter and am still a little confused. I'm designing a PCB on which I'd like to have an nrf52840 that can...
Hi,
I recently purchased the nRF9160DK but cannot connect to o2's LTE-M network using the iBasis SIM, following the instructions given here: https://www.nordicsemi.com/Software...
When I trap an error in app_error.c in app_error_save_and_stop,
I mostly get a filename, line number, and an error code that I can understand.
However, sometimes I...
We are looking for a freelancer who can help to build a simple Proof of Concept of a load cell (strain gauges) ADC (HX711?) and the nRF52 development kit (810).
Objectives...
Central and peripheral is pairing and bonded. Central scanning with whitelist, if Slave is not online, master scan with whitelist will enter error when more than 30 seconds...
I'm using whitelist when bonded, but I want delete bonded then connect to anther device,.
But when scan again, whitelist_load is error. Try delete whitelist at the same...
