Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I'm attempting to transfer 256K bps (1 244-byte notification every ~7.5ms) using an nRF52840 using Notifications and am not getting close to the necessary bandwidth. I'm getting...
Hi,
We are developing an application requiring the DFU Service on nRF52832.
The implementation of the DFU Service without bonds works very well, but when switching to...
I've been able to connect to our server using the LTE modem sample app.
As shown below, I configure the modem, open a socket, bind the port, and send and receive a small...
As I'm working on debugging a problem where a TLS connection silently fails with no error code, it occurs to me that it would be VERY handy to have a way to connect wireshark...
In using the Thingy52 I can't figure out how to just get the just XY coordinates from the motion sensor - or any other sensor. I'm trying to figure out if I can capture motion...
hi, i am a student, i am new to nrf52840 DK. I downloaded Gooligmelec "nrf52test-led-battery" from github and open Solution inside SES . it was running ok. when suddenly....
Hello,
I am using nrf52840 and SDK 15.3.0. and the device wakes up every hour and every day for reporting data.
So I am using app timer to wake up also using app_timer...
Hi,
I am working on nrf52840 and using below SDK and softdevice.
SDK - 16.0
Softdevice - S140
IDE - embedded segger studio.
currently using nRF52840-DK.
I am using...
Hi Team,
We are using the Micro ECC functionalities , for that we need the SHA 256 Library,Micro ECC library won't have inbuilt SHA.So how to enable the SHA for Micro...
We are using a nordic 52840 chip with a S140 softdevice as a client to connect with GATT servers from smartphones. When we connect to one of our smartphones, we do get the...
Hi all,
i've try to update the NRF52_DK interface MCU firmware to MBED firmware (nrf5x_atsam3u2c_if_mbed_V0221_11012017.bin).
After power cycle, LD5 at interface MCU...
Any hints on connecting to HID keyboard example from linux command line ??
Running stock ble_app_hids_keyboard/pca10040/s112/ on eval board. Works fine with iPhone but can...
Hi! I'm configuring RTC on nrf51822. I'm setting up the LFCLK and RTC module by configuring their registers. I have set up a simple IRQ handler, but it seems that it never...
Hi,
I have few question on nRF9160 Thingy:91 and Dev Board.
1. From the schematic, I see that have used SP8T Switch from Antenna Feed pin (GPS and LTE) to the SIngle Antenna...
Hi, we want the DFU code in SDK 10.0 for NRF51 S110 to finish faster. The case we are optimizing is when there is dfu ongoing, just a simple boot.
Currently the main time...
