I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi,
I'm working on enabling APP Protection while successfully executing below code:
if (!nrf_sdh_is_enabled()) { if (VERSION_BUILD <= MAX_RELEASE_BUILD) { NRF_UICR-...
Dear all,
I'm using and nRF51822 chip for implementing a wireless HID device with dongle.
The device has an RGB LED, and indication scenarios for different modes are played...
I'm using SDK 15.3.0 example twi_scanner with Segger Embedded Studio. I do a search entire solution for TWI_SCL_M and the only location it shows up is in main under the twi_master_init...
I'm having this issue with oldish SDK 12 but since I reproduce the issue with SDK 15: I re-used the code from https://devzone.nordicsemi.com/nordic/short-range-guides/b/software...
Hello,
I am using nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice
I am trying to interface with external Flash (MX25l64) using SPI.so when ever i am trying to send...
Hi
Any sample or known project that can transform nrf52 usb dongle and be driven through COM port?
Imagine a C program in Linux that opens the USB port where dongle...
Hi,
I'm developing a custom board based on nrf52. Currently, we are using Segger through J-Link to program nrf52 DK.
As for my custom board, I left a 2x3 pinout including...
As unicast address is a address of a element in a node.
We have to assign unicast address to 500 nodes each contains 2 elements, and we configured publish and subscribe...
Hello,
I am using nrf52832, having SDK 15.3.0 in Segger Studio IDE. Win10
I am using fds_test_find_and_delete() function, to find and delete particular record from flash...
I latest firmware and loaded and software thingy91_ltem_v0.2.2.hex. And I get reboot all the time. It was working when I first got the kit then when I was testing this weekend...
Firstly, I am a very beginner in the BLE domain. I have very little knowledge of it.
I want to do a project where multiple BLE peripheral devices(nRF52) will communicate...
Hello:
I have questions about eSIM card.
As we know, GSMA standard eSIM card is an empty chip, we can use eSIM card after ISP information is installed into eSIM card....
Hello,
I have the same question as mentioned in this article:
https://devzone.nordicsemi.com/f/nordic-q-a/19252/how-to-avoid-interrupt-handling-is-not-missed-with-sd_app_evt_wait...
Hi,
I use nrf sniffer to monitor BLE communication. After pairing with encryption, wireshark indicates Encrypted packet decrypted incorrectly (bad MIC).
I think there...
I configured Uart on 23 - Rx and 24 - Tx of NRF52832.
In simple uart example it works fine with uart_event_handle for rx.
But when this code is merged with Nrf Mesh Dimmer...
