Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello everyone, i work on nRF24L01 and i have 3 ardunio with 3 nRF24L01 and 3 IMU as transmitter and 1 ardunio with 1 nRF24L01 as reciever, i am trying to recieve data from...
I have migrated a project that uses Thread DFU from SDK for Thread and Zigbee 1.0.0 to 2.0.0.
I have successfully loaded the new MBR, bootloader, settings and program via...
Not sure where the problem is. Some of my boards, the microphone works fine, on others it doesn't. I am using a Knowles SPK0641HT4H-1 PDM microphone. I am using it as mono...
Hi,
I am experiencing an error of up to 8% on SAADC readings on the NRF52832. We have performed a sweep of the full range of the ADC and produced the following graph which...
Hi
My application requires that SPI CS is NOT TOGGLED within a transaction, only at either side
My Transaction consists of:
1 - Slave sets up buffer ready for Rx and...
we are entertaining the idea of using an nRF52840 with a Semtech SX1276 (or possibly SX1262) as a BLE/LoRa endpoint node. We believe this is doable but wanted to make sure...
Hello, I am using SDK15.2 on nrf52 DK with SD 6.1.0 and having an issue while sending back to back data using NUS service. I have edited the ble_app_uart application and trying...
So I am brand new at this product line, and basically new at C in general, I come from VB land. So bare with me please
I purchased both a Nordic nrf52 dev kit evaluation...
Hello there,
I'm sending IMU data (16bytes) using a notification from a custom board to a phone. My final goal is to send this packet of data (16 bytes) every 10 milliseconds...
I am developing a mobile application with bluetooth mesh.
But i can not describe the structure of a node with demo application. The sequence that I want to understand is...
Dear Nordic,
I implemented a RTC calender in nRF52832 using RTC2 . I want to port this RTC calender to nRF52810 but 810 has 2 RTC.
RTC0 is used by softdevice and RTC1...
After getting the latest nRF9160 in (DK V0.7.0) I installed pynrfjprog, and then issued the following command (as provided in the README)
nrf9160_mdm_dfu --update
...
Hi, I am new to BLE mesh. As I have understand , a provisioner is one which forms the mesh network and assigns addresses to the node and make them join to the network.
1...
