Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I am trying to understand the Passkey LESC pairing on S140 soft device using the latest SDK 14.0.2.
The message sequence charts has a block "App starts DHKey calculation...
Hi developer, sorry to interrupt and ask. How to use an ultrasonic sensor with nRF52? Since I search a code for nRF52 are not exist and see ultrasonic sensor can connect with...
I modified TWI_SENSOR_PCA10040 example from 14.10 SDK to run on my NRF52832 device, and it reads from the device address perfectly. However when I wrap reading inside a FreeRTOS...
Hello ,
What is the preferable way to flash code into NRF52832 IC during mass production? Flashing the code into custom IC with NRF52-DK in time consuming process.
And...
Hi,
All of a sudden (isn't it always the case :) the JLink debugger fails to flash the app code to the dev kit (PCA100028)
The Project's softdevice is flashing well without...
I have configured 3 differential ADC channels
to sample with timer/PPI/DMA buffer.
When I turned everything off, I couldn't get below
20uA current (with only LFCLK running...
2017-12-07 22_28_04-D__Users_Eyal_myWorkspaces_KeilMDK_ble_peripheral_ble_app_hrs_rtx_pca10028_s130_.png
Hi,
I've developed a BLE Central app based on the SDK HRS collector...
Hello,
I am using NRF52 TWI master to read data from my sensor, I have read the twi_sensor example but it doesn't make use of nrf_drv_twi_xfer() .
My question is quite...
Dear nordic employee
1、when I use the spim to send 1 byte address to read it's value(4 bytes),like this:
nrf_drv_spi_ transfer(&spi,headerBuffer,(uint8_t)headerLength...
Hi!
I use this debug on another examples fine. But want to enable this debug in a my project. In a config.h file RTT debug enabled. But doesn't work debug. I remarked that...
Hello All,
Please check above image, showing antenna layout of my custom board.
I am receiving error frames at ~40ft distance on sniffer.
Please check whether antenna...
When creating a custom bootloader for buttonless DFU, it is surprising to see that nrf_dfu.c not compile without defining button related function.
The warning
nRF5_SDK_14...
After succesfull compile, installation and run of my first application , I cannot see anymore the nRF52 DK board from windows.
The application keep flashing the led but no...
I wanted to share the most reliable and efficient method I found to collect and store my log outputs through segger RTT, which also allows using the excellent Log Viewer Log4View...
Hello all:
I have faced a problem that my device will report hard fault when I try to start advertising after force disconnect the device.
My EV board is nRF52832 and...