Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I am using PCA10028. I am not able to verify the output for given examples of SDK 12.2.0 that require master emulator or UART.
I have the pin 0.30 connected to ground as...
nRFready Smart Remote 3 nRF52 v1.1(PCA63519)
SDK: nRF5x SDK v12.2.0
IDE:Keil 5
Hi,I am trying to flash the whole package of SR3.
1.Flash the s132_nrf52_3.0.0_softdevice...
I'm changing the DEVICE_NAME macro in the example and then flashing but for some reason when I scan for available Bluetooth devices, the device always turns up as Nordic_UART...
Hi All,
Can one safely assume when sending a packet to a destination address using the ping command in the CLI, that the payload echoed back is the payload transmitted...
mainc.txt
we can use INTENSET to enable certain events on the radio as in line 460 in mainc file attached. But how to enable this on the radio as a whole.
I basically...
Hi Nordic,
I am trying to enable the DC/DC converter on a QFAAH10 (revision 3) .
I am using the s130 v2.0.1 SD .
----------
1. sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi,
If I configure the radio notification to ACTIVE and then set a DISTANCE of 800us, is there any way that I can configure PPI to toggle a pin for example?
I know that...
We are applying the CE certifcate for a product using nRF51822 and softdevice S130. Certification lab requires us to fill in below techanical questions. Please help to answer...
Hello, my program stuck at these assembly codes:
I decided that it was stuck because I keep pressing F11 and it just go around in circles in these 4 lines.
So:
...
Can't I connect to device that hasn't been discovered yet??
I'm trying to connect one device( A ) to another device( B ) which ADDRESS is known but never discovered yet...
Hi there,
We're looking at doing something with beacons so that we can make use of the way iOS handles scans for them in the background differently to other peripherals...
The debugger does not work with the latest GNU toolchain for ARM Cortex-M build. It throws the following error on Eclipse:
Could not determine GDB version after sending...
GPIOTE Library makes my Board(nRF51422-QFAC) Brick??
I just build my nRF51422 Board, and It's pretty working well before I've used GPIOTE Library.
Before using GPIOTE...
Hi everyone,
I am seeing an issue where the SPI (master) ignores the first byte of RX buff and begins storing the received bytes from RxBuff[1] instead of RxBuff[0]. In...
