Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I'm trying to recreate the PWM_library example from the v.11 SDK in a new file in Keil. I have compared the debug settings in my project to the debug settings to...
Hi there,
I am following the thread to use JlinkExe and JlinkRTTClient. I encountered a situation which i don't understand.
After running JlinkExe (go to the folder...
Hello,
I am trying to remake an nrf52 project in Keil and ran into a problem regarding stdint.h. There is already an "include <stdint.h>" statement and Keil has not reported...
Hi,
I am testing the NUS using the UART example in the SDK11 with the PCA10040 board.
Since I want to achieve the maximum speed of transmission I used the FIFO buffer...
I am having issues waking up nRF52 with s132 using the RTC interrupt. The same code is used on nRF51 with s130 and does not show this behavior.
The RTC is configured and...
Hi,
is it possible to have the same configuration as in the example ble_central_and_peripheral but with ant+ as peripheral (on nRF52)?
Thank you for your attention
I am doing externally triggered SPIM transfer on the Nrf52 using PPI.
I found that the NRF_SPIM_TASK_SUSPEND is a very power hungry operation as SPI suspend waits for the...
Hello
I have a nRF52-DK and I am trying to programme an external designed by myself but this one contains the nRF51422 chip. I am using nRFGO Studio to upload the .HEX...
I consider using " nRF OpenMesh " to implement my project.
But, I have no idea bout what's the throughput of it.
Anyone has an idea?
I find the max. content of advertisement...
Hello, I'm trying to make two nRF52832 connect to each other on their own. Currently, it seems that the ble addresses are reversed when printed by ble_gap_addr_print in different...
Hello,
I'm looking for a solution to achieve best possible resolution timestamps of received advertising packets for BLE. Is there any specific chip that you would recommend...
Hi there!
I searched the forum and didn't find any clear answer.
nrf52 programming pins are SWDIO and SWDCLK and chip can be programmed.
When nrf52 is part of a pcb...
HI,
I am trying to Port the BLE BEACON source code of PCA 20006 to PCA 10028 EK.
I have changed the IROM settings.
I have initialized the soft device handler to NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I am trying to understand how can I have a running counter based on the low power 32.768 KHz oscilator that does not trigger any timeout interrupts (I am using the soft...
