Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi all,
I am currently working on a personal project with hundreds of nodes. I have created a device with remote provisioning models (server and client). In my network...
I'm encountering an issue while trying to use the CAF LED module with the nPM1300 PMIC. Despite configuring the Device Tree, prj.conf, and led_state_def.h, I'm still getting...
I would like to confirm if my understanding is correct regarding calculating the average current consumption using the PPK2.
As shown in the image, the Selection Average...
I can't find any mention about MU-MIMO in the datasheet. Does the nRF7002 support MU-MIMO TX and RX?
I cannot find any details of if support is mandatory for a 802.11ax...
Hello,
I need to implement Find My Device for nRF52833.
From Sample I could find "samples/bluetooth/fast_pair/Locator Tag" example. I tried to go through it. but I could...
Hi,
We are using the nrf52833 for development.
The first version of the program can connect to the discovery service normally. But we need to add some new features. And...
Lesson 8 of "nRF Connect SDK Intermediate" DevAcademy course deals with Bootloaders. I've successfully done the exercise of updating firmware using the off-the-shelf mcuboot...
hi,i wanna read the imu sensor lsm6ds3 on board of nrf52840 based Xiao BLE Sense
so i used the code in samples /sensor/lsm6dsl
first i didn't know if i do have to create...
I'm trying to use the nrf_desktop application 100% standard, with NO changes to the codebase at all.
My initial assumption is, that once I flash the nrf52840dongle, it should...
I am working with ESB between 2 nRF5340DK's (w/ no need to be cross compatible w/ other devices) and with NCS v2.5.0. I am using ESB to wirelessly transmit data every 2ms...
I am a student currently studying BLE.
At present, I am working on a multi-connection setup where both the master and the slaves are using the nRF52832. Specifically, I...
Greetings starting from the 'ble aggregator' example I developed a BLE central on NRF52840 with NRF5 SDK 17.02, capable of managing multiple peripherals which, once connected...
I'm running SDK 2.8 and 2.8 Toolchain. I created the sysbuild.conf setting:
SB_CONFIG_BOOTLOADER_MCUBOOT=y
and put it in the application folder (per this support request...
Hello, I am relatively new to the nRF 5340 Audio DK. I recently ordered a singular nRF 5340 Audio DK board and my goal was for the board to take in input audio via the PDM...
