Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello,
I have a custom board with an nRF52833 and a W25Q512JVEIQ, which communicate over SPI (not QSPI). I successfully accessed the W25Q512JVEIQ (executed my own read and...
Hi, I am using nRF52832 module BL652. I want to measure the battery voltages of a 9V battery. What are the best possible resistors value to measure voltage of such battery...
Hello, We have a custom PCB with both the nRF9160 and nRF52832. Currently, the nRF52 functions as an HCI controller connected via LPUART to the nRF9160. We're at the stage...
Dear sir:
When I first use CHIP tool in my Ubuntu NB, I can commission bulb(52840) through OTBR(Pi4+52840 RCP) successfully, besides, I can use CHIP tool to control bulb...
Hello,
I am currently checking the RSSI measurement precision, and we got very large errors (up to 10dB error) on the RSSI vs input power.
To avoid any PCB / matching...
I'm new to nRF5340 development, and I'm reviewing partitioning for multi-image DFU. I've enabled the bootloader with CONFIG_BOOTLOADER_MCUBOOT=y , and after checking partitions...
Hey,
I am having an issue where my device doesn't show up in the Nrf Connect app as "connectable" despite as far as I can tell being set as a connectable device. This doesn...
Hello,
I'm trying to upload code to an external board using an NRF52dk, and am having an error in vscode as shown below.
My issue seems to be very similar to the one...
Hello.
I understand that Radio Notifications is an API that notifies you before and after scheduled radio events occur within a SoftDevice, but can you tell me more about...
Good day
I have the NRF_desktop keyboard application running on the NRF52840 Dongle, Zephyr 2.6.1. I would like to us the nrf52840 ProMicro as it has a battery charger build...
Hi,
I would like to know Number of UARTs available for Murata 2AB. According to the 2AB datasheet, there is one UART, but the nRF52340 datasheet shows two UARTs. Can 2AB...
HI,
I am building "esb_ptx" sample in NRF54L15-PDK, by using CONFIG_DYNAMIC_INTERRUPTS, but it;s always reset like below;How to config the prj.conf to enable CONFIG_DYNAMIC_INTERRUPTS...
Dear all:
I found that the nrf52840 flash size is only 1MB, but the size of light bulb load is about 850KB, I have some questions:
1. Does it contains the FOTA region...
Hi
I am trying to use nrf52811 using nrf52840 DK board.
First, I check simple GPIO example working on my nrf52811 based custom boards
Second, I checked the Bluetooth...
How can I execute a command to commission a device for Thread by using the QR code or pairing code? (without using the pin_code or discriminator) Thanks.
